Bissoy.com
Doctors Medicines MCQs Q&A

Consider the amplifier circuit shown below. The transistor is specified to have Vt = 0.4 V, kn = 0.4 mA/V2, W/L = 10 and λ = 0. Also, let VDD = 1.8V, RD = 17.5kΩ, VGS = 0.6V and vgs = 0V. Find ID.

Consider the amplifier circuit shown below. The transistor is specified to have Vt = 0.4 V, kn = 0.4 mA/V2, W/L = 10 and λ = 0. Also, let VDD = 1.8V, RD = 17.5kΩ, VGS = 0.6V and vgs = 0V. Find ID. Correct Answer 0.08 mA

n:

Related Questions

Consider the amplifier circuit shown below. The transistor is specified to have Vt = 0.4 V, kn = 0.4 mA/V2, W/L = 10 and λ = 0. Also, let VDD = 1.8V, RD = 17.5kΩ, VGS = 0.6V and vgs = 0V. Find VDS.
We know ID =1/2 kn (VGS + vgs – Vt)2. Let the signal vgs be a sine wave with amplitude Vgs, and substitute vgs = Vgs sin ω t in Eq.(5.43). Using the trigonometric identity show that the ratio of the signal at frequency 2ω to that at frequency ω , expressed as a percentage (known as the second-harmonic distortion) is
Consider the amplifier below for the case VDD = 5 V, RD = 24 kΩ, (W/L) = 1 mA/V2, and Vt = 1 V. For amplifier biased to operate with an overdrive voltage of 0.5V, and disregarding the distortion caused by the MOSFET’s square-law characteristic, what is the largest amplitude of a sine-wave voltage signal that can be applied at the input while the transistor remains in saturation?
The following statements refer to an n channel FET operated in the active region: 1. The gate voltage VGS reverse biases the junction 2. The drain voltage VDD is negative with respect to the source 3. The current in the n channel is due to electrons 4. Increasing the reveres bias VGS increases the cross section for conduction Which of these statements are correct?
Consider the following statements regarding n-channel JFET: 1. The maximum drain current IDSS occurs when gate-to-source voltage VGS = 0 V and drain-to-source voltage VDS ≥ |VP|. (VP is pinch-off voltage). 2. For gate-to-source voltage VGS less than the pinch-off level, the drain current is 0 A. 3. For all levels of VGS between 0 V and the pinch-off level, the current ID will range between IDSS and 0 A, respectively. which of the above statements are correct ?
Consider an NMOS transistor having kn= 2 mA/V2. Let the transistor be biased at VOV = 1V. For operation in saturation, what dc bias current ID results? If a +0.1-V signal is superimposed on VGS, find the corresponding increment in collector current by evaluating the total collector current ID and subtracting the dc bias current ID.
For a p-channel FET, the current ID at Vgs = 2V and Vds = 5V and Vgs = 3V was found to be 2mA, what will be the value of ID at Vgs = 0V and Vds = 5V?
Consider the amplifier below for the case VDD = 5 V, RD = 24 kΩ, (W/L) = 1 mA/V2, and Vt = 1 V. If the amplifier is biased to operate with an overdrive voltage VOV of 0.5 V, find the incremental gain at the bias point.
Given VDD = 25V, VP = -3V. When VGS = -3V, IDS = 10mA. Find the operating point of the circuit.
Consider the circuit shown. VDS=3 V. If IDS=2mA, find VDD to bias circuit.