Related Questions

A shaft of diameter D is subjected to a twisting moment (T) and a bending moment (M). If the maximum bending stress is equal to maximum shear stress developed, then M is equal to
A $$\frac{{\text{T}}}{2}$$
B T
C 2T
D 4T
A load which is spread over a beam in such a manner that it varies uniformly over the whole length of abeam is called uniformly ________ load.
A Distributed
B Varying
C Both A and B
D None of these
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is
A $$\frac{{\text{M}}}{{\text{T}}}$$
B $$\frac{{\text{T}}}{{\text{M}}}$$
C $$\frac{{2{\text{M}}}}{{\text{T}}}$$
D $$\frac{{2{\text{T}}}}{{\text{M}}}$$
The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to
A $$\frac{{\text{T}}}{2}$$
B 1T
C 2T
D 4T
The bending moment at a section tends to bend or deflect the beam and the internal stresses resist its bending. The resistance offered by the internal stresses, to the bending, is called
A Compressive stress
B Shear stress
C Bending stress
D Elastic modulus
If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than
A $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
B $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} + \frac{{2{\text{D}}}}{3}} \right)^2}$$
C $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
D $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{\text{D}}}{3}} \right)^2}$$
When a shaft is subjected to combined twisting moment (T) and bending moment (M), then the equivalent twisting moment is equal to
A $$\frac{1}{2}\sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
B $$\sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
C $$\frac{1}{2}\left( {{\text{M}} + \sqrt {{{\text{M}}^2} + {{\text{T}}^2}} } \right)$$
D $${\text{M}} + \sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
In a simple bending theory, one of the assumptions is that the plane sections before bending remain plane after bending. This assumption means that
A Stress is uniform throughout the beam
B Strain is uniform throughout the beam
C Stress is proportional to the distance from the neutral axis
D Strain is proportional to the distance from the neutral axis
When a beam is subjected to bending moment, the stress at any point is __________ the distance of the point from the neutral axis.
A Equal to
B Directly proportional to
C Inversely proportional to
D Independent of

Next steps