Bissoy.com
Doctors Medicines MCQs Q&A

The bending moment at a section tends to bend or deflect the beam and the internal stresses resist its bending. The resistance offered by the internal stresses, to the bending, is called

The bending moment at a section tends to bend or deflect the beam and the internal stresses resist its bending. The resistance offered by the internal stresses, to the bending, is called Correct Answer Bending stress

Related Questions

Consider the following statements: 1. The thickness of the gusset plate should not be more than the thickness of the structural members being connected. 2. A plate girder is essentially a beam and its moment of resistance depends upon its section modulus. 3. The function of the flanges in a plate girder is to resist the bending moment and hence their respective areas can be reduced near the supports of a simply supported beam. Which of the above statements are correct?
Consider the following statements with regards to the shear force diagram for the beam ABCD: 1. The beam ABCD is an overhanging beam having supports at A and D only. 2. The beam carries a point load of 20 kN at C. 3. The beam carries a concentrated load of 10 kN at the end B. 4. The beam is an overhanging beam having supports at C and D only. 5. The beam carries a uniformly distributed load of 70 kN over the left hand portion AC only. Which of the above statements are correct?
In which of the following cases, there exists the situation of Pure Bending in some part of the beam or along the entire beam? i) A simply supported beam subjected to two equally spaced downward concentrated loads ii) A simply supported beam subjected to two equally spaced opposite moments iii) A cantilever beam subjected to clockwise moment at free end iv) An overhanging beam with both side overhangs subjected to different concentrated loads at both the free ends
Consider the following statements regarding types of supports and beams: 1. When both supports of beams are roller supports, the beam is known as simply supported beam. 2. A beam with one end fixed and the other end free is known as fixed beam. 3. A beam with both ends fixed is known as cantilever beam. 4. A beam with one end fixed and the other simply supported is known as propped cantilever. Which of the above statements is/are correct ?
Which of the following is the imaginary beam of same span as the original beam loaded with M/EI diagram of the original beam, such that the shear force and bending moment at a section will represent the rotation and deflection at that section in the original beam?
A reinforced concrete beam is subjected to 5 kNm bending moment due to dead load and 25 kNm bending moment due to live load. What should be the design bending moment for limit state of collapse? 
Consider the following statements regarding stress in beam : 1. If a member is subjected to equal and opposite couples acting in the same longitudinal planes, the member is said to be in pure bending. 2. The internal stresses developed in the beam are known as flexural stresses. 3. There is an intermediate surface known as neutral surface, at which the stress is zero. 4. An axis obtained by intersection of the neutral surface and a cross-section is known as neutral axis. Which of the above statements are correct ? 
A group of 74 students of Class XI went on picnic. The number of students who went on picnic by each section is as follows: Section A = 15 Section B = 24 Section C = 15 Section D = 20 5 students from Section A spent as much as 4 students from Section B. 12 Section B students spent as much as 9 Section C students and 6 Section C students spent as much as 8 Section D student. If every student of a particular section spent the same amount and all the students spent Rs. 23,370 altogether, find the amount spent by each student of Section D?
If the bend of a bend test has to be gauged to its complete extent _________ of bend must be computed.
If a rectangular under–reinforced section is subjected to bending moment equal to its moment carrying capacity and the stress in steel and extreme compression fiber of concrete at this moment are σs and σc respectively then which of the following is correct? Where, fy and fc are the permissible stresses in steel and concrete respectively.