Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?

LohaHridoy
  1. The updated information will be added to the existing routing table.
  2. The update will be ignored and no further action will occur.
  3. The updated information will replace the existing routing table entry.
  4. The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence.
  5. They will all load-balance.

0 like 0 dislike
1 views
Share with your friends

1 Answers

AhmedNazir

Call

Answer: Option 2

When a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However, if two routes are received and they both have the same AD, then the router will choose the one route with the lowest metrics, or in RIP's case, hop count.

0 like 0 dislike
1 views
Talk Doctor Online in Bissoy App
When the addenda on pinion and wheel is such that the path of approach and path of recess are half of their maximum possible values, then the length of the path of contact is given by (where r = Pitch circle radius of pinion, R = Pitch circle radius of wheel and $$\varphi $$ = Pressure angle)?

Answer: Option 4 Let'

1 Answers 8 views
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

Answer: Option 2 RIP has an administrative distance (AD) of 120, while IGRP has an administrative distance of 100, so the router will discard any route with a higher AD...

1 Answers 1 views
How should a router that is being used in a Frame Relay network be configured to keep split horizon issues from preventing routing updates?

Answer: Option 1 If you have a serial port configured with multiple DLCIs connected to multiple remote sites, split horizon rules, stop route updates received on an interface from being...

1 Answers 1 views
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?

Answer: Option 3 If you save a configuration and reload the router and it comes up either in setup mode or as a blank configuration, chances are you have the...

1 Answers 1 views
You have configured a Group Policy Object (GPO) for the marketing oranization unit (OU) to prevent users from accessing My Network Places and from running System in Control Panel. You want the Managers Domain Local Group to be able to access My Network Places, but you still want to prevent them from running System in Control Panel. What should you do?

Answer: Option 4 Let'

1 Answers 1 views
What command is used to stop RIP routing updates from exiting out an interface but still allow the interface to receive RIP route updates?

Answer: Option 3 The (config-router) #passive-interface command stops updates from being sent out an interface, but route updates are still received.

1 Answers 2 views
You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?

Answer: Option 2 The command traceroute (trace for short), which can be issued from user mode or privileged mode, is used to find the path a packet takes through an...

1 Answers 3 views
The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?

Answer: Option 3 Before you start to configure the router, you should erase the NVRAM with the erase startup-config command and then reload the router using the reload command.

1 Answers 1 views
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?

Answer: Option 2 At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router. If you have...

1 Answers 5 views
You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?

Answer: Option 4 The show ip eigrp neighbors command allows you to check the IP addresses as well as the retransmit interval and queue counts for the neighbors that have...

1 Answers 1 views