You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?

LohaHridoy
  1. Router> ping
  2. Router> trace
  3. Router> show ip route
  4. Router> show interface

0 like 0 dislike
3 views
Share with your friends

1 Answers

AhmedNazir

Call

Answer: Option 2

The command traceroute (trace for short), which can be issued from user mode or privileged mode, is used to find the path a packet takes through an internetwork and will also show you where the packet stops because of an error on a router.

0 like 0 dislike
3 views
Talk Doctor Online in Bissoy App
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

Answer: Option 2 RIP has an administrative distance (AD) of 120, while IGRP has an administrative distance of 100, so the router will discard any route with a higher AD...

1 Answers 1 views
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?

Answer: Option 3 If you save a configuration and reload the router and it comes up either in setup mode or as a blank configuration, chances are you have the...

1 Answers 1 views
Which command will show you the IOS version running on your router?

Answer: Option 3 The best answer is show version, which shows you the IOS file running currently on your router. The show flash command shows you the contents of flash...

1 Answers 1 views
You have a system that periodically locks up. You have ruled out software, and now suspect that it is hardware. What should you do first that could help you narrow it down to the component at fault?

Answer: Option 4 Let'

1 Answers 1 views
You are the administrator responsible for security and user desktop settings on your network. You need to configure a custom registry entry for all users. You want to add the custom registry entry into a Group Policy object (GPO) with the least amount of administrative effort What should you do?

Answer: Option 1 Let'

1 Answers 6 views
You have configured a Group Policy Object (GPO) for the marketing oranization unit (OU) to prevent users from accessing My Network Places and from running System in Control Panel. You want the Managers Domain Local Group to be able to access My Network Places, but you still want to prevent them from running System in Control Panel. What should you do?

Answer: Option 4 Let'

1 Answers 1 views
You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?

Answer: Option 3 The command show ip protocols will actually show you the broadcast address for each interface - too bad it isn't a possible answer. Your best answer is...

1 Answers 1 views
The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?

Answer: Option 3 Before you start to configure the router, you should erase the NVRAM with the erase startup-config command and then reload the router using the reload command.

1 Answers 1 views
A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?

Answer: Option 2 The show flash command will provide you with the current IOS name and size and the size of flash memory.

1 Answers 5 views
If your routing table has a static, a RIP, and an IGRP route to the same network, which route will be used to route packets by default?

Answer: Option 3 Static routes have an administrative distance of 1 by default. Unless you change this, a static route will always be used over any other found route. IGRP...

1 Answers 1 views
X