- Configure a separate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface.
- Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.
- Configure many subinterfaces in the same subnet.
- Configure a single subinterface to establish multiple PVC connections to multiple remote router interfaces.
1 Answers
Call
Answer: Option 1
If you have a serial port configured with multiple DLCIs connected to multiple remote sites, split horizon rules, stop route updates received on an interface from being sent out the same interface. By creating subinterfaces for each PVC, you can avoid the split horizon issues when using Frame Relay.
0
like
0 dislike
Talk Doctor Online in Bissoy App
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Answer: Option 2 When a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However,...
1 Answers 1 views
When setting up Frame Relay for point-to-point subinterfaces, which of the following must not be configured?
Answer: Option 3 It is very important to remember when studying the CCNA exam objectives, and when configuring Frame Relay with point-to-point subinterfaces, that you do not put an IP...
1 Answers 2 views
When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the clock rate determined?
Answer: Option 1 Clocking on a serial interface is always provided by the CSU/DSU (DCE device). However, if you do not have a CSU/DSU in your nonproduction test environment, then...
1 Answers 1 views
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
Answer: Option 2 RIP has an administrative distance (AD) of 120, while IGRP has an administrative distance of 100, so the router will discard any route with a higher AD...
1 Answers 1 views
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
Answer: Option 3 If you save a configuration and reload the router and it comes up either in setup mode or as a blank configuration, chances are you have the...
1 Answers 1 views
You have configured a Group Policy Object (GPO) for the marketing oranization unit (OU) to prevent users from accessing My Network Places and from running System in Control Panel. You want the Managers Domain Local Group to be able to access My Network Places, but you still want to prevent them from running System in Control Panel. What should you do?
Answer: Option 4 Let'
1 Answers 1 views
What command is used to stop RIP routing updates from exiting out an interface but still allow the interface to receive RIP route updates?
Answer: Option 3 The (config-router) #passive-interface command stops updates from being sent out an interface, but route updates are still received.
1 Answers 2 views
The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
Answer: Option 3 Before you start to configure the router, you should erase the NVRAM with the erase startup-config command and then reload the router using the reload command.
1 Answers 1 views
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
Answer: Option 2 At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router. If you have...
1 Answers 5 views
You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?
Answer: Option 3 If you have a Cisco router on one side of a Frame Relay network and a non-Cisco router on the other side, you would need to use...
1 Answers 1 views