Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
Which of the following statement(s) is/are true regarding butt welding? 1. Flash butt welding is a combination of resistance, arc and pressure welding 2. Upset butt welding is used for welding rods 3. Percussion Welding is a self timing spot welding method 4. Aluminium alloys are flash welded
The figure shows a 5 cm diameter rod, 90 cm long, which is having its lower face grinded smooth. The remainder of the rod is exposed to 32 degree Celsius room air and a surface coefficient heat transfer equal to 6.8 W/m2 degree exists between the rod surface and the room air. The grinder dissipates mechanical energy at the rate of 35 W. If thermal conductivity of rod material is 41.5 W/m degree, find the temperature of the rod at the point where the grinding is taking place
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
Consider the following statements regarding welded and riveted joints 1. Welded assemblies are tight and leak proof as compared with riveted assemblies. 2. Single-welded V-joint is less reliable than square butt joint. 3. Welding results in a thermal distortion of the parts, thereby inducing residual stresses. Which of the above statements is/are correct ?
A tensile rod of 40kN is acting on a rod of diameter 40mm and of length 4m. a bore of diameter 20mm is made centrally on the rod. To what length the rod should be bored so that the total extension will increase 30% under the same tensile load if E = 2×105 N/mm2?
A 150 mm long cylinderical rod having a diameter of 100 mm contains six microvoids which are situated at radial distances of 5 mm, 8 mm, 12 mm. 20 mm, 30 mm, 36 mm respectively, on a given r-z plane. Along the length (z-direction) of the rod, the voids are spaced uniformly. The specimen is to be tested by an ultrasonic cylinderical probe, 7.5 mm in diameter: The maximum number of flows, that can be detected in a single measurement by placing the probe at one end of the rod (flat surface) is
Thickness of 8 tyres L, M, N, O, P, Q, R and S is compared. Thickness of no two tyres is same. Thickness of N is more than L but less than 6 tyres. Thickness of O is more than M but less than Q. Thickness of P is less than only two tyres. Thickness of Q is not more than P. Which of the following statement is not correct?
For a steam engine, the following data is given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m calculate inertia force at θ=30 degrees from IDC.
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.