Bissoy.com
Doctors Medicines MCQs Q&A

Determine the slew rate of the amplifier having full power bandwidth f0 and the rated output voltage as V0. Given that the input signal is of sinusoidal nature.

Determine the slew rate of the amplifier having full power bandwidth f0 and the rated output voltage as V0. Given that the input signal is of sinusoidal nature. Correct Answer 2πf0 V0

v = V0sin wt dv/dt = wV0 sin wt max value of dv/dt = wV0 max value of w = w0 = 2πf0 w0 V0 = Slew Rate = 2πf0 V0.

Related Questions

A company paid tk.500000 in merit raises to employees whose performances were rated A, B, or C. Each employee rated A received twice the amount of the rated C.each employee rated B received 150% of the amount of the raise thst was paid to each employee rated C. if 50 workers were rated A,100rated B and 150 were rated C, how much was the raise paid to each employee rated B?
For an instrumentation amplifier, the following parameters are given (a) High input resistance and low power consumption (b) Low input resistance and low power consumption (c) High CMRR and high slew rate (d) Low CMRR and high slew rate Which of the given parameters are a major requirement for an instrumentation amplifier?
An amplifier using an opamp with slew rate SR=1v/sec has a gain of 40db.If this amplifier has to faithfully amplify sinusoidal signals from dc to 20KHz without introducing any slew-rate induced distortion, then the input signal level exceed
An amplifier using an opamp with slew rate SR=1v/µsec has a gain of 40db.if this amplifier has to faithfully amplify sinusoidal signals from dc to 20 KHz without introducing any slew-rate induced distortion, then the input signal level must not exceed
The ABC company has released their Android app. And 80 people have rated the app on a scale of 5 stars. Out of the total people 15 people rated it with 1 star, 20 people rated it with 2 stars, 30 people rated it with 3 stars, 10 people rated it with 4 stars and 5 people rated it with 5 stars. What will be the final prediction if we take the average of individual predictions?
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If Vi = 0.5 V, what is the maximum frequency before the output distorts?
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If f = 20 kHz, what is the maximum value of Vi before the output distorts?
A sinusoidal input voltage Vin of frequency ω is fed to the circuit shown in the figure, where C1 ≫ C2. If Vm is the peak value of the input voltage, then output voltage (Vout) is
Electronics mcq question image
Consider the following statements. It converts the positive half cycle of the sinusoidal wave of the input to the pulsating DC output signal. It converts the positive half as well as negative half cycle of the sinusoidal wave of the input to pulsating DC output signal. Which of the following statements is CORRECT about half-wave rectifier?
Consider the following Statements regarding the ideal operational amplifier 1. Output common-mode noise voltage is zero 2. Infinite bandwidth 3. Unity Common mode rejection ratio 4. infinite slew rate 5. Infinite output impedance Which of the above properties are correct?