Bissoy.com
Doctors Medicines MCQs Q&A

An amplifier using an opamp with slew rate SR=1v/µsec has a gain of 40db.if this amplifier has to faithfully amplify sinusoidal signals from dc to 20 KHz without introducing any slew-rate induced distortion, then the input signal level must not exceed

An amplifier using an opamp with slew rate SR=1v/µsec has a gain of 40db.if this amplifier has to faithfully amplify sinusoidal signals from dc to 20 KHz without introducing any slew-rate induced distortion, then the input signal level must not exceed Correct Answer 79.5 mV

Related Questions

An amplifier using an opamp with slew rate SR=1v/sec has a gain of 40db.If this amplifier has to faithfully amplify sinusoidal signals from dc to 20KHz without introducing any slew-rate induced distortion, then the input signal level exceed
For an instrumentation amplifier, the following parameters are given (a) High input resistance and low power consumption (b) Low input resistance and low power consumption (c) High CMRR and high slew rate (d) Low CMRR and high slew rate Which of the given parameters are a major requirement for an instrumentation amplifier?
A signal containing only two frequency components (3 kHz and 6 kHz) is sampled at the rate of 8 kHz, and then passed through a low pass filter with a cut-off frequency of 8 kHz. The filter output
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If f = 20 kHz, what is the maximum value of Vi before the output distorts?
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
A sinusoidal signal of 2 kHz frequency is applied to a delta modulator. The sampling rate and step-size Δ of the delta modulator are 20,000 samples per second and 0.1 V, respectively. To prevent slope overload, the maximum amplitude of the sinusoidal signal (in Volts) is
Determine the slew rate of the amplifier having full power bandwidth f0 and the rated output voltage as V0. Given that the input signal is of sinusoidal nature.
An internally compensated op amp has a dc open-loop gain of 106 V/V and an AC open-loop gain of 40 dB at 10 kHz. Estimate its gain–bandwidth product and its expected gain at 1 kHz.
An amplifier of gain 1000 is made into a feedback amplifier by feeding 9.9% of its output voltage in series with the input opposing. If fL = 20 Hz and fH = 200 kHz for the amplifier without feedback, then due to the feedback
A government official said, “Currently, the traffic signals installed along the roads have a fixed signal timer but with the Japanese technology, signals will automatically change according to the number of vehicles along the road.” Which of the following could be the reason for the statement? I: The installation of smart signals will reduce the waiting time at signals and junctions. II: The installation of smart signals will solve the traffic woes in the city. III: The technology will be an integrated traffic management center that will ease congestion in the city.