Related Questions

The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)
A $${\text{m}}{\omega ^2}{\text{r}}\sin \theta $$
B $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
C $${\text{m}}{\omega ^2}{\text{r}}\frac{{\sin 2\theta }}{{\text{n}}}$$
D $${\text{m}}{\omega ^2}{\text{r}}\frac{{\cos2\theta }}{{\text{n}}}$$
The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)
A $${\text{m}}{\omega ^2}{\text{r}}\sin \theta $$
B $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
C $${\text{m}}{\omega ^2}{\text{r}}\frac{{\sin 2\theta }}{{\text{n}}}$$
D $${\text{m}}{\omega ^2}{\text{r}}\frac{{\cos2\theta }}{{\text{n}}}$$
The velocity of piston in a reciprocating steam engine is given by (where $$\omega $$ = Angular velocity of crank, r = Radius of crank pin circle, $$\theta $$ = Angle turned by crank from inner dead center and n = Ratio of length of connecting rod to the radius of crank)
A $$\omega {\text{r}}\left( {\sin \theta + \frac{{\sin 2\theta }}{{\text{n}}}} \right)$$
B $$\omega {\text{r}}\left( {\cos\theta + \frac{{\cos2\theta }}{{\text{n}}}} \right)$$
C $${\omega ^2}{\text{r}}\left( {\sin \theta + \frac{{\sin 2\theta }}{{\text{n}}}} \right)$$
D $${\omega ^2}{\text{r}}\left( {\cos\theta + \frac{{\cos2\theta }}{{\text{n}}}} \right)$$
A bell rings every 15 minute. If the bell rang at 12.40, which of the following could be a time at which the bell had sounded?
A 5:30
B 6:45
C 7:15
D 8:10
The tractive force in a locomotive with two cylinders is given by (where c = Fraction of reciprocating parts per cylinder, m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank and $$\theta $$ = Angle of inclination of crank to the line of stroke)
A $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
B $${\text{cm}}{\omega ^2}{\text{r}}\sin \theta $$
C $$\left( {1 - {\text{c}}} \right){\text{m}}{\omega ^2}{\text{r}}\left( {\cos \theta - \sin \theta } \right)$$
D $${\text{m}}{\omega ^2}{\text{r}}\left( {\cos \theta - \sin \theta } \right)$$
If d and n are the effective depth and depth of the neutral axis respectively of a singly reinforced beam, the lever arm of the beam, is
A d
B n
C $${\text{d}} + \frac{{\text{n}}}{3}$$
D $${\text{d}} - \frac{{\text{n}}}{3}$$
When the primary direct crank of a reciprocating engine makes an angle of $$\theta $$ with the line of stroke, then the secondary direct crank will make an angle of _________ with the line of stroke.
A $$\frac{\theta }{2}$$
B $$\theta $$
C $$2\theta $$
D $$4\theta $$
The number of centers in a crank driven slider crank mechanism is
A 0
B 2
C 4
D 6
Arm in arm means-
A হাতে হাত রাখা
B পরস্পর সম্পর্কিত বিষয়
C সুসম্পর্ক
D সৌজন্য বিনিময়
When the fulcrum is in between the load and effort, the lever is said to be of
A First type
B Second type
C Third type
D Any one of these

Next steps