Bissoy.com
Doctors Medicines MCQs Q&A

Which router command allows you to view the entire contents of all access lists?

Which router command allows you to view the entire contents of all access lists? Correct Answer <i class="networking-code">show access-lists</i>

To see the contents of all access lists, use the show access-lists command.

Related Questions

Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
You are working on a router that has established privilege levels that restrict access to certain functions. You discover that you are not able to execute the command show running-configuration. How can you view and confirm the access lists that have been applied to the Ethernet 0 interface on your router?
You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful?
1. TFTP server software must be running on the router.
2. TFTP server software must be running on your laptop.
3. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable.
4. The laptop must be on the same subnet as the router's Ethernet interface.
5. The copy flash tftp command must be supplied the IP address of the laptop.
A group of 2m - 1 routers are interconnected in a centralized binary tree, with router at each tree node. Router I communicate with router J by sending a message to the root of the tree. The root then sends the message back down to J. Then find the mean router-router path length.
You get a call from a network administrator who tells you that he typed the following into his router:
Router (config) #router ospf 1Router (config-router) #network 10.0.0.0 255.0.0.0 area 0
He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?
Consider a computer network using the distance vector routing algorithm in its network layer. The partial topology of the network is as shown below. The objective is to find the shortest-cost path from the router R to routers P and Q. Assume that R does not initially know the shortest routes to P and Q. Assume that R has three neighbouring routers denoted as X, Y, and Z. During one iteration, R measures its distance to its neighbours X, Y, and Z as 3, 2, and 5, respectively. Router R gets routing vectors from its neighbours that indicate that the distance to router P from routers X, Y, and Z are 7, 6, and 5, respectively. The routing vector also indicates that the distance to router Q from routers X, Y, and Z are 4, 6, and 8, respectively. Which of the following statement(s) is/are correct with respect to the new routing table of R, after updation during this iteration ? 
Consider the following statements about the functionality of an IP based router. I. A router does not modify the IP packets during forwarding. II. It is not necessary for a router to implement any routing protocol. III. A router should reassemble IP fragments if the MTU of the outgoing link is larger than the size of the incoming IP packet. Which of the above statements is/are TRUE?
An OSPF router receives an LSA, the router checks its sequence number, and this number matches the sequence number of the LSA that the receiving router already has. What does the receiving router do with the LSA?
What information is displayed by the show hosts command?
1. Temporary DNS entries
2. The names of the routers created using the hostname command
3. The IP addresses of workstations allowed to access the router
4. Permanent name-to-address mappings created using the ip host command
5. The length of time a host has been connected to the router via Telnet
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?