You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?

A Router (config-if) #encapsulation frame-relay q933a
B Router (config - if) #encapsulation frame-relay ansi
C Router (config - if) #encapsulation frame-relay ietf
D Router (config - if) #encapsulation frame-relay cisco

Correct Answer: Router (config - if) #encapsulation frame-relay ietf

If you have a Cisco router on one side of a Frame Relay network and a non-Cisco router on the otherside, you would need to use the Frame Relay encapsulation type of IETF. The default is Cisco encapsulation, which means that a Cisco router must be on both sides of the Frame Relay PVC.

Bissoy MCQ
#CCNA #CISCO Certification

Related Questions

When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the clock rate determined?
A Supplied by the CSU\/DSU
B By the far end router
C By the clock rate command
D By the Physical layer bits stream timing
A default Frame Relay WAN is classified as what type of physical network?
A Point-to-point
B Broadcast multi-access
C Non-broadcast multi-access
D Non-broadcast multipoint
Which of the following commands will configure all the default VTY ports on a router?
A Router#line vty 0 4
B Router (config) #line vty 0 4
C Router (config-if)#line console 0
D Router(config)#line vty all
Suppose that you have a customer who has a central HQ and six branch offices. They anticipate adding six more branches in the near future. They wish to implement a WAN technology that will allow the branches to economically connect to HQ and you have no free ports on the HQ router. Which of the following would you recommend?
A PPP
B HDLC
C Frame Relay
D ISDN
The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
A RAM should be erased and the router restarted
B Flash should be erased and the router restarted
C NVRAM should be erased and the router restarted
D The new configuration should be entered and saved
The cost of picture frame M is Tk. 10.00 less than 3 times the cost of picture frame N. If the cost of frame M is Tk. 50.00, what is the cost of frame N?
A Tk. 13.33
B Tk. 16.66
C Tk. 20.00
D Tk. 26.66
The cost of picture frame M is TK. 10.00 less than 3 times the cost of picture frame N. If the cost of frame M is TK. 50.00 , what is the cost of frame N?
A TK. 13.33
B TK. 16.66
C TK. 20.00
D TK. 26.66
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
A You didn
B NVRAM is corrupted.
C The configuration register setting is incorrect.
D The newly upgraded IOS is not compatible with the hardware of the router.
How should a router that is being used in a Frame Relay network be configured to keep split horizon issues from preventing routing updates?
A Configure a separate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface.
B Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.
C Configure many subinterfaces in the same subnet.
D Configure a single subinterface to establish multiple PVC connections to multiple remote router interfaces.
You are the administrator of contoso.local domain. You organize the domain into organizational units as shown in the EXHIBIT. You configure the local security options and other settings for the default domain policy object You delegate administration of Michigan and Florida OU. You want to prevent those administrators from creating any other group policy objects with settings that conflict with those you configured.What should you do?
A From the group policy options from the contoso.local domains set the option not override
B From the group policy options from the Michigan and Florida OU, set the option not override
C Block the group policy inheritance for the contoso.local domain
D Block the group policy inheritance for Michigan and Florida OU
E None of above

Next steps