Related Questions

If the section modulus of a beam is increased, the bending stress in the beam will
A Not change
B Increase
C Decrease
D None of these
‘P’ is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is ‘A’ and sectional modulus is ‘Z’. The minimum stress ‘f’ on the beam subjected to a maximum bending moment ‘M’ is
A $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{Z}}}{{\text{M}}}$$
B $${\text{f}} = \frac{{\text{A}}}{{\text{P}}} - \frac{{\text{M}}}{{\text{Z}}}$$
C $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{\text{Z}}}$$
D $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{6{\text{Z}}}}$$
‘P’ is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is ‘A’ and sectional modulus is ‘Z’. The maximum stress ‘f’ in the beam, subjected to a maximum bending moment ‘M’, is
A $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{Z}}}{{\text{M}}}$$
B $${\text{f}} = \frac{{\text{A}}}{{\text{P}}} - \frac{{\text{M}}}{{\text{Z}}}$$
C $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{\text{Z}}}$$
D $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{6{\text{Z}}}}$$
The bending moment at a section tends to bend or deflect the beam and the internal stresses resist its bending. The resistance offered by the internal stresses, to the bending, is called
A Compressive stress
B Shear stress
C Bending stress
D Elastic modulus
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is
A $$\frac{{\text{M}}}{{\text{T}}}$$
B $$\frac{{\text{T}}}{{\text{M}}}$$
C $$\frac{{2{\text{M}}}}{{\text{T}}}$$
D $$\frac{{2{\text{T}}}}{{\text{M}}}$$
The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to
A $$\frac{{\text{T}}}{2}$$
B 1T
C 2T
D 4T
A shaft of diameter D is subjected to a twisting moment (T) and a bending moment (M). If the maximum bending stress is equal to maximum shear stress developed, then M is equal to
A $$\frac{{\text{T}}}{2}$$
B T
C 2T
D 4T
The rectangular beam 'A' has length ‘l’, width ‘b’ and depth ‘d’. Another beam 'B' has the same length and depth but width is double that of 'A'. The elastic strength of beam 'B' will be _________ as compared to beam ‘A’.
A Same
B Double
C Four times
D Six times
In a simple bending theory, one of the assumptions is that the plane sections before bending remain plane after bending. This assumption means that
A Stress is uniform throughout the beam
B Strain is uniform throughout the beam
C Stress is proportional to the distance from the neutral axis
D Strain is proportional to the distance from the neutral axis

Next steps