Bissoy.com
Doctors Medicines MCQs Q&A

The measure of moisture content during thermogravimetric analysis is by the process of _________

The measure of moisture content during thermogravimetric analysis is by the process of _________ Correct Answer water vaporization

In thermogravimetric analysis, the moisture is determined by the loss of mass of a substance (normally moisture) when heated. This can be achieved by the water vaporization process. It is a complete, precise and approachable method to determine moisture.

Related Questions

It takes 6 hours to dry a wet solid from 50% moisture content to the critical moisture content of 15%. How much longer it will take to dry the solid to 10% moisture content, under the same drying conditions? (The equilibrium moisture content of the solid is 5%).
A solid is being dried in the linear drying rate regime from moisture content Xo to XF. The drying rate is zero at X = 0 and the critical moisture content is the same as the initial moisture Xo. The drying time for M = (Ls/ARc) is (where, L = total mass of dry solid, A = total surface area for drying Rc = Constant maximum drying rate per unit area X = moisture content (in mass of water/mass of dry solids)
200 kg of solids (on dry basis) is subjected to a drying process for a period of 5000 seconds. The drying occurs in the constant rate period with the drying rate as, Nc = 0.5 × 10-3 kg/m2.s. The initial moisture content of the solid is 0.2 kg moisture/kg dry solid. The interfacial area available for drying is 4 m2/1000 kg of dry solid. The moisture content at the end of the drying period is (in kg moisture/kg dry solid)
Find the initial moisture content for the batch process if the final moisture content is 25% (dry basis) and the constant moisture content is 40%. (Includes constant and falling rate period)
Find the final moisture content for the batch process if the initial moisture content is 75% (dry basis) and the constant moisture content is 40%. (Includes constant and falling rate period)
The x- axis is the moisture content on dry basis. The y-axis is the equilibrium moisture content. Which of the following shows Bound moisture content?
A dryer is used for drying pears which has initial moisture content of 70 % (wet basis) and final moisture content of 5 % (wet basis). An experimental drying curve for the product indicates that the critical moisture content is 25 % (wet basis) and the time for constant drying is 5 min. Can you estimate the total drying time for product?
In a laboratory test run, the rate of drying was found to be 0.5 × 10-3 kg/m2.s, when the moisture content reduced from 0.4 to 0.1 on dry basis. The critical moisture content of the material is 0.08 on a dry basis. A tray dryer is used to dry 100 kg (dry basis) of the same material under identical conditions. The surface area of the material is 0.04 m2/kg of dry solid. The time required (in seconds) to reduce the moisture content of the solids from 0.3 to 0.2 (dry basis) is
In the question below are given six statements followed by four conclusions numbered I, II, III and IV. You have to take the given statements to be true even if they seem to be at variance with commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: All Petrol are Gasoline. No petrol is Water. Some Water are Gas. Some Moisture are Gas. All Gasoline are Fire No Moisture is Fire Conclusions: I. Some Moisture are Gasoline. II. Some Water are Moisture. III. Some Gasoline are Gas. IV. Some Petrol are Moisture.
Which of the following statements is most relevant in the context of Job Analysis? Choose the correct answer from the code given below. (i) Job Analysis helps in identifying the right person for the right job. (ii) A person cannot judge the job from the point of view of its suitability. (iii) Job analysis helps in job satisfaction and job efficiency. (iv) Through Job Analysis an employer cannot evaluate the prospective employee to judge his fitness or otherwise for the job. (v) Job Analysis helps in planning appropriate training programs. (vi) Job Analysis defines client needs in specific terms. (vii) Job Analysis assists in knowing the personnel specifications for various jobs.