Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
Consider we have a Double Pipe Heat Exchanger, with the inner tube of Outer diameter 20mm (thickness 2mm) and outer tube of inner diameter 30mm. We have two fluids A & B, we desire to have their flow rates as 15 Kg/s and 21 Kg/s respectively. Calculate the convective heat transfer coefficient from tube to annulus side. (Given Nusselt number on tube side = 496 and K = 15W/mK)
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
Consider we have a 1-2 Shell and Tube Heat Exchanger with tube diameter 20mm and shell diameter 55mm, we have two fluids A&B, A is supply water and B is distilled water, we desire to have their flow rates as 15m3/s and 21m3/s respectively. Which fluid pass arrangement would be best suited for the HE?
Investigate the effect of following condition on the average value of heat transfer coefficient in flow through a tube Two fold increases in flow velocity by varying mass flow rate It may be presumed that there is no change in the temperature of the liquid and the tube wall, and that the flow through the tube is turbulent in character
Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is
Consider we have a Double Pipe Heat Exchanger, with the inner tube of Outer diameter 20mm (thickness 2mm) and outer tube of inner diameter 30mm. We have two fluids A & B, we desire to have their flow rates as 15Kg/s and 21Kg/s respectively. What is the value of Hydraulic diameter for the annulus tube?
One test tube contains some chemical and another test tube contains an equal quantity of water. To prepare a solution, 20 g of the chemical is poured into the second test tube. Then, two-thirds of the formed solution is poured from the second test tube into the first. If the fluid in the first test tube is four times that in second, what quantity of water was taken initially.
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.