Consider we have a 1-2 Shell and Tube Heat Exchanger with tube diameter 20mm and shell diameter 55mm, we have two fluids A&B, A is supply water and B is distilled water, we desire to have their flow rates as 15m3/s and 21m3/s respectively. Which fluid pass arrangement would be best suited for the HE?

Consider we have a 1-2 Shell and Tube Heat Exchanger with tube diameter 20mm and shell diameter 55mm, we have two fluids A&B, A is supply water and B is distilled water, we desire to have their flow rates as 15m3/s and 21m3/s respectively. Which fluid pass arrangement would be best suited for the HE? Correct Answer Counterflow with B in tube and A in the shell side

When we are required to provide the best arrangement for a Shell and Tube HE, we consider keeping the fluid with fouling properties on the shell side, this helps to clean the fouling caused on the equipment for the longevity of the equipment and also reduce maintenance costs.
Bissoy MCQ

Related Questions

Consider we have a Double Pipe Heat Exchanger, with the inner tube of diameter 20mm (neglect thickness) and outer tube of diameter 30mm. We have two fluids A & B, we desire to have their flow rates as 15m3/s and 21m3/s respectively. Which fluid pass arrangement would be best suited for the HE?
Consider we have a Double Pipe Heat Exchanger, with the inner tube of Outer diameter 20mm (thickness 2mm) and outer tube of inner diameter 30mm. We have two fluids A & B, we desire to have their flow rates as 15 Kg/s and 21 Kg/s respectively. Calculate the convective heat transfer coefficient from tube to annulus side. (Given Nusselt number on tube side = 496 and K = 15W/mK)
Consider we have a Double Pipe Heat Exchanger, with the inner tube of Outer diameter 20mm (thickness 2mm) and outer tube of inner diameter 30mm. We have two fluids A & B, we desire to have their flow rates as 15Kg/s and 21Kg/s respectively. What is the value of Hydraulic diameter for the annulus tube?
Consider we have a Double pipe Heat Exchanger, with inner tube of diameter 20mm (neglect thickness) and outer tube of diameter 30mm. We have two fluids A & B (KA = 15W/mK and KB = 20W/mK) we desire to have their flow rates as 15m3/s and 21m3/s respectively. If their Nusselt number after calculation is Nui = 429 and Nuo = 530. What is the overall heat transfer coefficient of the equipment is no fouling exists?
Consider we have a Double Pipe Heat Exchanger, with the inner tube of diameter 20mm (neglect thickness) and outer tube of diameter 30mm. We have two fluids A & B (both with viscosity 2.5×10-5Pa-s), we desire to have their flow rates as 15 Kg/s and 21 Kg/s respectively. What is the Reynolds number for this setup for the inner pipe?
A designer chooses the values of fluid flow rates and specific heats in such a manner that the heat capacities of the two fluids are equal. A hot fluid enters the counter flow heat exchanger at 100°C and leaves at 60°C. A cold fluid enters the heat exchanger at 40°C. The mean temperature difference between the two fluids is
A single pass shell and tube heat exchanger, consisting of a bundle of 100 tubes (inner diameter 25 mm and thickness 2 mm) is used for heating 28 kg/s of water from 25 degree Celsius to 75 degree Celsius with the help of a steam condensing at atmospheric pressure on the shell side with condensing heat transfer coefficient 5000 W/m2 degree. Make calculation for overall heat transfer coefficient based on the inner area. Take fouling factor on the water side to be 0.002 m2 degree/W per tube and neglect effect of fouling factor on the shell side and thermal resistance of the tube wall
Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is
Plate type heat exchangers have less surface area as compared to a similar Shell and Tube heat exchanger. A Shell and Tube Heat Exchanger of equivalent area weigh six-seven times less than a Plate Type heat exchanger.
Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is