Bissoy.com
Doctors Medicines MCQs Q&A

What are the temperature and pressure conditions in compression moulding technique in the moulding of phenolic moulding powder?

What are the temperature and pressure conditions in compression moulding technique in the moulding of phenolic moulding powder? Correct Answer 160-170 ᵒC and 1500-3000 psi

Compression moulding is operated to mould the phenolic moulding powders by using a pressure of about 1500-3000 psi and temperature of 160-170 ᵒC.

Related Questions

In the following question, two statements are numbered as A and B. On solving these statements we get quantities A and B respectively. Solve for the both quantities and choose the correct option. Quantity A: Two powders P and Q are to be mixed in ratio 4 ∶ 7 to form a mixture. If 28 kg of powder P and 28 kg of powder Q is available, how much powder Q is more required to make the desired mixture? Quantity B: A mixture is formed by mixing 16 kg of powder X and 25 kg of powder Y. How much powder X is required to be mixed with 40 kg of powder Y to make a mixture of the same ratio?
108 kg of mixture C was prepared by mixing equal quantities of mixtures A and B, made up of chalk powder and brick powder, such that the ratio of chalk and brick powder in mixture C is 17 ∶ 10. If mixture A comprised of 22 kg chalk powder, how much brick powder was present in mixture B?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The rate list of groceries in a shop are depicted as follows : Rice (1 KG) Rs. 70 Black gram (1 KG) Rs. 90 Wheat Flour (1 KG) Rs. 45 Coriander powder (250 g) Rs. 40 Chilli Powder (250 g) Rs. 60 Salt (1 Pkt Rs. 25 Biscuit (1 Pkt) Rs. 20 Ashish needs to buy 5 kg of rice, 5 kg of wheat flour, 250 g of coriander powder, 250 g of chilli powder, 2 kg of black gram and some packets of biscuit with remaining money. If he is having Rs. 1000, how many biscuit packets can be buy?
Match the following in Column X with Column Y: Column X Column Y  P. In a triaxial compression test, with increase of axial strain in loose sand under drained shear condition, the volumetric strain  I. decreases  Q. In a triaxial compression test, with increase of axial strain in loose sand under undrained shear condition, the excess pore water pressure  II. Increase  R. In a triaxial compression test, the pore pressure parameter “B” for a saturated soil  III. remains same  S. For shallow strip footing in pure saturated clay, Terzaghi’s bearing capacity factor (Nq) due to surcharge  IV. is always 0.0.      V. is always 1.0.      VI. is always 0.5. Which one of the following combinations is correct?
The question below consists of a set of labelled sentences. These sentences, when properly sequenced form a coherent paragraph. Select the most logical order of sentences from among the options. P: On Mars, the thin, dry atmosphere provides very different conditions for powder falling out of the drill. Q: The sample transfer technique allows Curiosity to position its drill over two small inlets on top of the rover’s deck, R: This delivery method had already been successfully tested at JPL. However, that’s here on Earth; S: trickling in the appropriate amount of rock powder for the onboard laboratories to do their analyses. 
In vapor compression cycle having dry saturated vapor at the end of compression the work done is given by? H2 – Enthalpy of vapor after compression H1 – Enthalpy of vapor before compression
In vapor compression cycle having dry saturated vapor at the end of compression the refrigeration effect is given by? H1 – Enthalpy of vapor before compression H4 – Enthalpy of vapor before entering evaporator H2 – Enthalpy of vapor after compression
What are the temperature and pressure conditions for the compression moulding of m-f resin?
Dinu starts his spice business. He buys 10 kg turmeric powder, 8 kg red chilli powder and 15 kg coriander powder. He makes small packets of 20 g of each of the spices. How many small packets of spices he prepares to sell?