Bissoy.com
Doctors Medicines MCQs Q&A

For a six–sigma spread in the distribution of the product quality characteristic, the upper natural control limit will fall at _____________

For a six–sigma spread in the distribution of the product quality characteristic, the upper natural control limit will fall at _____________ Correct Answer μ + 3σ

For six sigma distribution of the product quality characteristic, the upper natural tolerance control limit will fall at, UNTL = μ + 3σ.

Related Questions

Rock mass parameters for a shale rock, mb, s, and a of the Hoek and Brown failure criterion as given in the equation are 2.4, 0.01 and 0.52 respectively. The uni-axial compressive strength (σCi) of intact sh!le is 50 MPa.
$${\sigma _1} = {\sigma _3} + {\sigma _{ci}}{\left( {{m_b}\frac{{{\sigma _3}}}{{{\sigma _{ci}}}} + S} \right)^a}$$
The global rock mass strength of shale in MPa is
Which of the following is/are the advantages of using a control chart for inspection? (i) A control chart indicates whether the process is in control or out of control. (ii) A control chart determines process variability. (iii) A control chart ensures product quality. (iv) Scrap or percentage reduction can be reduced by taking the necessary actions in time against the warnings indicated by control charts. (v) Control charts build up the reputation of the organization through customer’s satisfaction. (vi) The control chart can detect the unusual variations taking place in a process.
The table below shows the frequency distribution of a certain mass data. Class Interval 0-25 25-50 50-75 75-100 100-125 Frequency 2 7 6 3 8 As a tradition, the lower limit is always included in the class interval (CI); and the upper limit is removed from every CI, except the last. For the given data, x is the upper limit of the model class and y is the lower limit of the median class. Then what is the value of (2x - 5y)?
A 70 kg tea powder contains mixture from two qualities. Some amount of quality 1 tea powder is added so that ratio of quality 1 to quality 2 becomes 5 : 4. What is the extra amount of of quality 2 to be added so that, quality 2 becomes double the amount of quality 1 in new mixture. Given: current quality 1 exceeds quality 2 in old mixture by 10 kg?
Consider the below statements. (i) Quality is defined as fitness for the purpose at the lowest cost (ii) Quality is a grade of the product in appearance, performance, life, reliability, taste, odour, maintainability etc (iii) Quality is the degree to which a specified product is preferred over competing products of equivalent grade, based on the comparative test by customers, normally called as customer’s preference (iv) Quality is a measure of the degree of the general excellence of the product (v) Quality may be defined as the degree of conformance to design and specifications Which of the above statements are correct?
The nominal size of a product is 30 mm. The acceptable industrial limits are from 29.98 mm to 30.02 mm. After manufacturing, the quality engineer finds the lower limit of the manufactured product to be 29.00 mm while the upper limit is 30.01 mm. What can you infer from the given scenario?
The Lower control limit has a 6 unit distance from the upper control limit of the standardized control chart.
Consider the following statements: 1. When a soil sample is dried beyond its shrinkage limit, the volume of the soil slowly decrease 2. The plastic limit is always lower than the liquid limit for any type of soil 3. At the liquid limit, the soil behaves like a liquid and possesses no shear strength at all 4. When subjected to drying, the volume of the soil remains unchanged once the water content of the soil goes below its shrinkage limit Which of the above statements are correct? 
What are the different limit states of design as per IS 456: 2000? a. Limit state of failure b. Limit state of damage c. Limit state of collapse d. Limit state of serviceability
Consider the following statements.  I. Pi-Bond is stronger than the Sigma Bond.  II. Sigma Bond is formed by linear overlapping of atomic orbitals.  III. In the case of Pi-Bond, the extent of overlapping of atomic orbitals is more as compared to the Sigma Bond.  Which among the above is/are NOT correct?