Bissoy.com
Doctors Medicines MCQs Q&A

Two silicon diodes, with a forward voltage drop of 0.7 V, are used in the circuit shown in the figure. The range of input voltage ?? for which the output voltage ?? = ??, is

Two silicon diodes, with a forward voltage drop of 0.7 V, are used in the circuit shown in the figure. The range of input voltage ?? for which the output voltage ?? = ??, is Correct Answer -1.7 V &lt; V<sub style="">i</sub> &lt; 2.7 V

Try to solve all the diode related questions with the following approach:

1) Consider all the diodes to be off.

2) Now, first, calculate the voltage across each diode.

3) If the diodes have greater voltage than cut-in voltage, consider that the diode to be on which has higher voltage.

4) Now, again calculate the voltage across the remaining diode by considering that particular diode to be ON.

5) Again check which diode has a greater voltage considering it ON, and the process continues till we get to know the state of each diode.

Analysis:

Given: Vr = 0.7 V

[ alt="F4 S.B Madhu 30.07.20 D5" src="//storage.googleapis.com/tb-img/production/20/07/F4_S.B_Madhu_30.07.20_D5.png" style="width: 285px; height: 137px;">

When Vi > 2.7 V, the output voltage will be fixed to:

V0 = 2.7 V

When Vi < -1.7 V, the output voltage will again be fixed to:

V0 = -1.7 V

When -1.7 V < Vi < 2.7 V, both the diodes are OFF and:

V0 = Vi

∴ The transfer characteristics can be drawn as:

[ alt="F4 S.B Madhu 30.07.20 D6" src="//storage.googleapis.com/tb-img/production/20/07/F4_S.B_Madhu_30.07.20_D6.png" style="width: 339px; height: 204px;">

Related Questions

In the figure, D1 is a real silicon p-n junction diode with a drop of 0.7 V under forward bias condition and D2 is a Zener diode with breakdown voltage of -6.8 V. The input Vin(t) is a periodic square wave of period T, whose one period is shown in the figure. Assuming 10τ ≪ T, where τ is the time constant of the circuit, the maximum and minimum values of the output waveform are respectively,
A clipper circuit is shown below: Assuming forward voltage drops of the diodes to be 0.7 V, the input-output transfer characteristics for the circuit will be
The I – V characteristics of the zener diodes D1 and D2 are shown in Figure I. These diodes are used in the circuit given in Figure II. If the supply voltage is varied from 0 to 100 V, then breakdown occurs in.
Silicon devices can be employed for a higher temperature limit (190°C to 200°C) as compared to germanium devices (85°C to 100°C). With respect to this, which of the following are incorrect? 1) Higher resistivity of silicon 2) Higher gap energy of silicon 3) Lower intrinsic concentration of silicon 4) Use of silicon devices in high-power applications Select the correct answer using the code given below:
A sinusoidal input voltage Vin of frequency ω is fed to the circuit shown in the figure, where C1 ≫ C2. If Vm is the peak value of the input voltage, then output voltage (Vout) is
Electronics mcq question image
The output of the following Python code is similar to the alphabet . . . . . . . .
import turtlet=turtle.Pen()t1=turtle.Pen()t2=turtle.Pen()t.forward(100)t1.forward(100)t2.forward(100)t1.left(90)t1.forward(75)t2.right(90)t2.forward(75)
Which of the following statements are not correct? (A) Precision rectifiers use positive feedback to compensate for the forward drop of the diodes (B) Precision peak detector uses a capacitor to effectively lengthen the duration of the peaks (C) Limiters may be thought of as programmable signal clippers (D) In order to improve performance of comparators negative feedback may be used (E) There are two basic approaches for realizing a design : (1) using zener diodes and (2) using biased-signal diode network Choose the most appropriate answer from the options given below: (1) (A) and (D) only (2) (D) and (E) only (3) (A) and (C) only (4) (B) and (D) only
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
In a 3-phase voltage source inverter used for speed control of induction motor anti parallel diodes are used across each switching device as shown in figure. The main purpose of diodes is to