Bissoy.com
Doctors Medicines MCQs Q&A

The rivet head for a general-purpose shown in the figure below is:

The rivet head for a general-purpose shown in the figure below is: Correct Answer Counter sunk

A rivet is a permanent mechanical joint which are broadly used to joint structure, ships, barrels etc. These joints are widely used in ship and boiler industries to join the structure member.

The general nomenclature of rivet is given as follows

[ alt="16" src="//storage.googleapis.com/tb-img/production/17/07/16.PNG" style="height:127px; width:142px">

Types of Rivet heads:

[ alt="F6 Madhuri Engineering 15.06.2022 D1" src="//storage.googleapis.com/tb-img/production/22/06/F6_Madhuri_Engineering_15.06.2022_D1.png" style="height: 330px; width: 329px;">

 

Related Questions

When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which (where, Fa is the load shared by each rivet due to axial load and Fm is the shearing load due to moment in any rivet.)
Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
Which of the following assumptions are made in the design of rivet joints? A. Rivets are stressed equally B. Stress in plate is maximum at mid-width C. Rivet hole is completely filled by rivet D. Friction between plates is neglected
Which one of the following four addresses is NOT EXACTLY the same as the one given below? Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (i) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (ii) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (iii) Robert S Ingram 1998 Revocable 8 Shaftsbary Ln Hilton Head Island, SC 29926 (843) 342­7094 (iv) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094
Among flat head and snap head rivet, which has the higher head height?
In order to avoid tearing of the plate at edge, the distance from the center line of the rivet hole to the nearest edge of the plate in terms of dia. of rivet d should be equal to
According to Indian standards, the diameter of rivet hole is made larger than the basic size of rivet by
A riveted joint in which every rivet of a row is opposite to other rivet of the outer row, is known as
In order to avoid tearing of the plate at an edge, the distance from the centre line of the rivet hole to the nearest edge of the plate should be equal to (where d = Diameter of rivet hole)
The diameter of the rivet hole is usually __________ the nominal diameter of the rivet.