Bissoy.com
Doctors Medicines MCQs Q&A

When the section is subjected to an axial load and a moment, the ratio of the moment to the load is called:

When the section is subjected to an axial load and a moment, the ratio of the moment to the load is called: Correct Answer Eccentricity

Explanation:

We know  Moment (M) = P × e 

Where P is Load, e is the eccentricity

→ e = M/P

∴ The ratio of the moment to the load is called eccentricity

Related Questions

Consider the following statements: In case of helical gears, teeth are cut at an angle to the axis of rotation of the gears. 1) Helix angle introduces another ratio called axial contact ratio. 2) Transverse contact ratio is equal to axial contact ratio in helical gears. 3) Large transverse contact ratio does not allow multiple teeth to share the load. 4) Large axial contact ratio will cause larger axial force component Which of the above statements are correct?
A group of 74 students of Class XI went on picnic. The number of students who went on picnic by each section is as follows: Section A = 15 Section B = 24 Section C = 15 Section D = 20 5 students from Section A spent as much as 4 students from Section B. 12 Section B students spent as much as 9 Section C students and 6 Section C students spent as much as 8 Section D student. If every student of a particular section spent the same amount and all the students spent Rs. 23,370 altogether, find the amount spent by each student of Section D?
Last year, there were three sections in a competitive exam. Out of them 33 students cleared the cut-off in Section A, 34 students cleared the cut-off in Section B and 32 students cleared the cut-off in Section C. 10 students cleared the cut-off in section A and section B, 9 cleared the cut-off in section B and section C and 8 cleared the cut-off in section A and section C. The number of students who cleared only one section was equal and was 21 for each section. How many students cleared all the three sections?
Consider the following for local capacity of section: 1. Local section failure is usually encountered in the case of short stocky beam-columns with relatively smaller axial compression ratio and beam-columns bent in reverse curvature. 2. The strength of end section reached under combined axial force and bending, governs the failure. 3. The strength of the section may be governed by plastic buckling of plate elements in the case of plastic, compact and semi-compact sections. Which of the above statements are correct?
In which of the following cases, there exists the situation of Pure Bending in some part of the beam or along the entire beam? i) A simply supported beam subjected to two equally spaced downward concentrated loads ii) A simply supported beam subjected to two equally spaced opposite moments iii) A cantilever beam subjected to clockwise moment at free end iv) An overhanging beam with both side overhangs subjected to different concentrated loads at both the free ends
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A reinforced concrete beam is subjected to 5 kNm bending moment due to dead load and 25 kNm bending moment due to live load. What should be the design bending moment for limit state of collapse? 
When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which (where, Fa is the load shared by each rivet due to axial load and Fm is the shearing load due to moment in any rivet.)
If a rectangular under–reinforced section is subjected to bending moment equal to its moment carrying capacity and the stress in steel and extreme compression fiber of concrete at this moment are σs and σc respectively then which of the following is correct? Where, fy and fc are the permissible stresses in steel and concrete respectively.
The extension of a circular bar tapering uniformly from diameter $${{\text{d}}_1}$$ at one end to diameter $${{\text{d}}_2}$$ at the other end and subjected to an axial pull of P is _________ the extension of a circular bar of diameter $$\sqrt {{{\text{d}}_1}{{\text{d}}_2}} $$  subjected to the same load P.