Bissoy.com
Doctors Medicines MCQs Q&A

Side rake angle of a single point cutting tool is the angle

Side rake angle of a single point cutting tool is the angle Correct Answer By which the face of the tool is inclined sideways

Related Questions

In a single point turning tool, the side rake angle and orthogonal rake angle are equal. ϕ is the principal cutting edge angle and its range is 000. The chip flows in the orthogonal plane. The value of ϕ is closest to
How far is point 'R' from Point 'T'? Statement (I): Point 'R' is 5 metres to the north of point 'M'. Point 'U' is 4 metres to the east of point 'R'. Point 'T' is to the west of point 'R' such that points 'U' 'R' and 'T' form a straight line of  metres. Statement (II): Point 'Z' is metres to the south of point 'T'. Point 'U' is  metres to the east of point 'T'. Point 'M' is  metres to the east of point 'Z'. Point 'R' is  metres to the north of point 'M'. Point 'R' lies on the line formed by joining points 'T' and 'U'.
Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
Point A is 3m in the north of point B. Point D is 2m in the east of point E. Point F is 9m in the west of point G. Point C is 4m in the west of point B. Point C is 3m in the south of point D. Point F is 5m in the south of point E. Point H is 5m in the north of point G. What is the shortest distance between point H and point A?
Which of the following forces are measured directly by strain gauges or force dynamometers during metal cutting? 1. Force exerted by the tool on the chip acting normally to the tool face 2. Horizontal cutting force exerted by the tool on the workpiece 3. Frictional resistance of the tool against the chip flow acting along the tool face 4. Vertical force which helps in holding the tool in position Select the correct answer using the codes given below.
Flank wear occurs mainly on the 1. Nose part of the cutting tool 2. Front relief face and side relief face of the cutting tool 3. Face of the cutting tool at the shortest distance from the cutting edge Which of the above is/are correct?
Point P is 4m in the west of point V. Point R is 6m in the north of point Q. Point T is 5m in the south of point S. Point V is in the middle of point R and Q. Point U is 5m in the east of point R. Point V is in north of point Q. Point S is 5m in the east of point V. What is the area of triangle formed by point P, R and Q?
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. How far and in which direction is Point G from Point A?
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. If point G is 4m to the north of Point H, then what is the distance between H and D?
In the metal cutting operation, what will be the shear angle when a cutting tool has positive rake angle α = 20°. The friction angle is 40°. (Use Merchant's shear angle theory)