Related Questions

10 cm লম্বা ও 0.5 cm ব্যাসার্ধ বিশিষ্ট একটি তামা ও একটি লোহার তারকে জোড়া লাগিয়ে দৈর্ঘ্য 20 cm করা হল। জোড়া লাগানো তারটিকে বল প্রয়োগ করে লম্বা করা হল। লোহার ইয়ংয়ের গুণাঙ্ক তামার ইয়ংয়ের গুণাঙ্কের দুইগুণ হলে লোহার দৈর্ঘ্য বৃদ্ধি ও তামার দৈর্ঘ্য বৃদ্ধির অনুপাত কত? ( A steel and a brass wire, both having 10 cm length and 0.5 cm radius, are joined together making the total length of the combined wire 20 cm. The combined wire is stretched by applying a force. If the Young's modulus of steel is twice as much as that of brass, what will be the ratio of the extension of steel to the extension of brass?)
A 1 :8
B 1 : 6
C 1 : 4
D 1 : 2
10 cm লম্বা ও 0.5 cm ব্যাসার্ধ বিশিষ্ট একটি তামা ও একটি লোহার তারকে জোড়া লাগিয়ে দৈর্ঘ্য 20 cm করা হল। জোড়া লাগানো তারটিকে বল প্রয়োগ করে লম্বা করা হল। লোহার ইয়ংকের গুণাস্ক তামার ইয়ংকের গুণাস্কের দুইগুন হলে লোহার দৈর্ঘ্য বৃধি ও তামার দৈর্ঘ্য বৃদ্ধির অনুপাত কত? (A steel and a brass wire, both having 10 cm length and 0.5 cm radius, are joined together making the total length of the combined wire 20 cm. The combined wire is stretched by applying a force. If the Young‘s modulus of steel is twice as much as that of brass, what will be the ratio of the extension of steel to the extension of brass?)
A 1:8
B 1:6
C 1:4
D 1:2
The cutting speed for drilling aluminium, brass and bronze with carbon steel drills is _________ cutting speed for drilling mild steel with high speed steel drills.
A Equal to
B Less than
C More than
D None of these
The average cutting speed for turning brass with a high speed steel tool is
A 15 to 19 m/min
B 25 to 31 m/min
C 60 to 90 m/min
D 90 to 120 m/min
The high cutting speed and large rake angle of the tool will result in the formation of
A continuous chips
B discontinuous chips
C continuous chips with built up edge
D none of the mentioned
Side rake angle of a single point cutting tool is the angle
A By which the face of the tool is inclined towards back
B By which the face of the tool is inclined sideways
C Between the surface of the flank immediately below the point and a plane at right angles to the centre line of the point of the tool
D Between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base
The cutting speed for drilling aluminium, brass and bronze with high speed steel drills varies from
A 10 to 20 m/min
B 18 to 30 m/min
C 24 to 45 m/min
D 60 to 90 m/min
For machining a mild steel workpiece by a high speed steel tool, the average cutting speed is
A 5 m/min
B 10 m/ min
C 15 m/min
D 30 m/min
The average cutting speed for turning mild steel with a high speed steel tool is
A 15 to 19 m/min
B 25 to 31 m/min
C 60 to 90 m/min
D 90 to 120 m/min
The rake angle of a single point cutting tool corresponds to _________ of a twist drill.
A Lip clearance angle
B Helix angle
C Point angle
D Chisel edge angle

Next steps