Bissoy.com
Doctors Medicines MCQs Q&A

The high cutting speed and large rake angle of the tool will result in the formation of

The high cutting speed and large rake angle of the tool will result in the formation of Correct Answer continuous chips

The low cutting speed and small rake angle of the tool are responsible for the formation of discontinuous chips while high cutting speed and large rake angle of the tool will result in the formation of continuous chips.

Related Questions

Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
In a single point turning tool, the side rake angle and orthogonal rake angle are equal. ϕ is the principal cutting edge angle and its range is 000. The chip flows in the orthogonal plane. The value of ϕ is closest to
Which of the following forces are measured directly by strain gauges or force dynamometers during metal cutting? 1. Force exerted by the tool on the chip acting normally to the tool face 2. Horizontal cutting force exerted by the tool on the workpiece 3. Frictional resistance of the tool against the chip flow acting along the tool face 4. Vertical force which helps in holding the tool in position Select the correct answer using the codes given below.
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
In the metal cutting operation, what will be the shear angle when a cutting tool has positive rake angle α = 20°. The friction angle is 40°. (Use Merchant's shear angle theory)
Flank wear occurs mainly on the 1. Nose part of the cutting tool 2. Front relief face and side relief face of the cutting tool 3. Face of the cutting tool at the shortest distance from the cutting edge Which of the above is/are correct?
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool, the cutting velocity is 90 m/min. The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm. If the orthogonal rake angle is zero and the principle cutting edge angle is 90°, the shear angle in degree is
Angle between the rake face flank of tool and perpendicular line drawn from cutting point to base of tool is known as:
Consider three software items: Program-X, Control Flow Diagram of Program-Y and Control Flow Diagram of Program-Z as shown below Program-X: Control Flow Diagram of Program-Y sumcal (int maxint, int value) {       int result=0, i=0;       if (value <0)       {           Value = -value;       }       while ( (i
In an orthogonal machining operation : Uncut thickness = 0.5 mm Cutting speed = 20 m/min Rake angel = 150 Width of cut = 5 mm Chip thickness = 0.7 mm Thrust force = 200 N Cutting force = 1200 N The values of shear angle and shear strain, respectively, are