Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
If Rati travels at his usual speed for ‘x’ hours, he covers the same distance as he covered when he travels at a speed 30 km/hr less than usual, but for (x + 3) hours. Which of the following can be determined? (A) If he travels at 20 km/hr less speed than usual, he can cover a distance of 240 km in (x - 1) hours. What is the value of ‘x’? (B) If travels at his usual speed for (t + 2) hours, and at 50% of his usual speed for (t - 2) hours, his average speed for the journey is 68 km/hr. What is his usual speed? (C) His usual speed (in km/hr) is a multiple of 5 between 40 and 50 (both inclusive). If ‘x’ is a whole number, what is his usual speed? (D) If he travels at his usual speed for ‘t’ hours, he covers a distance of 400 km. What is the value of ‘x’?
The speed of six bikes B1, B2, B3, B4, B5 and B6 has been compared. The speed of the B6 exceeds just three bikes. No two bikes have the same speed. The speed of B4 is more than that of B2 but less than that of B6. The speed of B3 is not less than that of B5. The speed B2 is not minimum. If the speed of B5 is not less than that of B2, then which of the following pair of bikes has more speed than that of B4?
Output of a bulldozer is (i) Increased if drawbar HP of the tractor is increased for a given hauling distance (ii) Decreased if drawbar HP of the tractor is increased for a given hauling distance (iii) Increased if the hauling distance is increased for a given drawbar HP of the tractor (iv) Decreased if the hauling distance is increased for a given drawbar HP of the tractor
Output of a bulldozer is
(i) Increased if drawbar HP of the tractor is increased for a given hauling distance
(ii) Decreased if drawbar HP of the tractor is increased for a given hauling distance
(iii) Increased if the hauling distance is increased for a given drawbar HP of the tractor
(iv) Decreased if the hauling distance is increased for a given drawbar HP of the tractor
Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
Flank wear occurs mainly on the 1. Nose part of the cutting tool 2. Front relief face and side relief face of the cutting tool 3. Face of the cutting tool at the shortest distance from the cutting edge Which of the above is/are correct?
Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image
Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image
Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image