Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
The cutting speed for drilling aluminium, brass and bronze with carbon steel drills is _________ cutting speed for drilling mild steel with high speed steel drills.
The speed of six bikes B1, B2, B3, B4, B5 and B6 has been compared. The speed of the B6 exceeds just three bikes. No two bikes have the same speed. The speed of B4 is more than that of B2 but less than that of B6. The speed of B3 is not less than that of B5. The speed B2 is not minimum. If the speed of B5 is not less than that of B2, then which of the following pair of bikes has more speed than that of B4?
If Rati travels at his usual speed for ‘x’ hours, he covers the same distance as he covered when he travels at a speed 30 km/hr less than usual, but for (x + 3) hours. Which of the following can be determined? (A) If he travels at 20 km/hr less speed than usual, he can cover a distance of 240 km in (x - 1) hours. What is the value of ‘x’? (B) If travels at his usual speed for (t + 2) hours, and at 50% of his usual speed for (t - 2) hours, his average speed for the journey is 68 km/hr. What is his usual speed? (C) His usual speed (in km/hr) is a multiple of 5 between 40 and 50 (both inclusive). If ‘x’ is a whole number, what is his usual speed? (D) If he travels at his usual speed for ‘t’ hours, he covers a distance of 400 km. What is the value of ‘x’?
Each of the question below consists of a question and three statements number I, II and III given below it. You have to decide whether the data provided in the statement are sufficient to answer the question. If the bus is travelling from Surat to Ahmadabad and a car is travelling from Ahmadabad to Surat, then what is the distance between Surat and Ahmadabad? I. The speed of a car is 40% less than the speed of bus. Bus started at 9 am and car started at 10 am and they meet at 3 pm of the same day. II. After travelling for 1 hour, because of traffic average speed of bus is decreased by 20% and covers distance between Surat to Ahmadabad in 11 hours. Original speed of car is 20% less than original speed of bus and before crossing bus it covered 200 km if starts 1 hour later than bus. After crossing car, bus covers remaining distance in 5 hours. III. Speed of bus is 10 km/hr more than the speed of car and before crossing car ratio of distances covered bus and car in same time was 5 : 4. Time taken by car to cover the distance between Ahmadabad and Surat is 2 hours 15 minutes more than time taken by bus to cover the same distance.
What is the general categorisation of equipments for manufacturing garments?
1. Measuring tools
2. Marking tools
3. Cutting tools
4. Pressing tools
High speed steel drills can be operated at about _________ the speed of high carbon steel drills.
Combined carbon content in iron and steel is determined by treating the sample with dilute HNO3. So that combined carbon forms a soluble brown nitrated compound, the intensity of which is matched with that of a standard sample of similar composition treated under similar condition. The intensity of color produced is proportional to the carbon content of iron of steel sample. This method of combined carbon determination is called the
In the following question, sentences of a paragraph have been jumbled and labelled as A, B, C and D. You are required to rearrange the jumbled sentences of the paragraph and mark your response accordingly by selecting the correct option. A: Iron is able to take on two crystalline forms (allotropic forms), body-centered cubic, and face-centered cubic, depending on its temperature.  B: Iron is the base metal of steel. C: Because of steel's high tensile strength and low cost, this material is best used in buildings, infrastructure, tools, ships, trains, cars, machines, electrical appliances, and weapons. D: Steel is an alloy of iron and carbon and, sometimes, other elements such as chromium.