In metal cutting, use of low feeds and high cutting speeds is desired when the objective is

A High metal removal rate
B Dry machining
C Use of soft cutting tool
D Surface finish

Correct Answer: Surface finish

Following Steps Has to be taken to Improve the surface Finish:Increase the Speed. Reduce the Feed. Increase the Top Rake Angle. Use a Chip Breaker. Use a Large Nose Radius. Use the Correct Technique.Use Different Tools to Rough and Finish.
Bissoy MCQ
#Mechanical Engineering #Manufacturing And Production Technology

Related Questions

High speed steel cutting tools operate at cutting speeds _________ than carbon steel tools.
A 2 to 3 times lower
B 2 to 3 times higher
C 5 to 8 times higher
D 8 to 20 times higher
A company produces five types of shirts -- A,B,C,D and E-using cloth of three qualities -- high, medium and low , using dyes of three qualities-- high, medium and low. One shirt requires 1.5 m of cloth .The following table gives respectively : The number of shirts (of each category) produced, in thousands. The percentage distribution of cloth quality in each type of shirt, and The percentage distribution of dye quality in each type of shirt. How many meters of low-quality cloth is consumed?
A 40,00 m
B 60,000 m
C 46,500 m
D 22,500 m
A company produces five types of shirts -- A,B,C,D and E-using cloth of three qualities -- high, medium and low , using dyes of three qualities-- high, medium and low. One shirt requires 1.5 m of cloth .The following table gives respectively : The number of shirts (of each category) produced, in thousands. The percentage distribution of cloth quality in each type of shirt, and The percentage distribution of dye quality in each type of shirt. What is the ratio of low quality dye used for C-type shirts to that used for D-type shirts ?
A 2:3
B 1:2
C 2:1
D 3:2
With an RS latch a high S and low R sets the output to _____ ; a low S and a high R _____ the output to low.
A No change, set
B Race, high
C high, reset
D set, reset
E None of the above
If a transistor amplifier feeds a load of low resistance (e.g. speaker), then voltage gain will be ___________
A High
B Very high
C Moderate
D Low
A company produces five types of shirts -- A,B,C,D and E-using cloth of three qualities -- high, medium and low , using dyes of three qualities-- high, medium and low. One shirt requires 1.5 m of cloth .The following table gives respectively : The number of shirts (of each category) produced, in thousands. The percentage distribution of cloth quality in each type of shirt, and The percentage distribution of dye quality in each type of shirt. How many metres of high quality cloth is consumed by A-type shirts?
A 30,00 m
B 24,00 m
C 112,000 m
D 8,00 m
A company produces five types of shirts -- A,B,C,D and E-using cloth of three qualities -- high, medium and low , using dyes of three qualities-- high, medium and low. One shirt requires 1.5 m of cloth .The following table gives respectively : The number of shirts (of each category) produced, in thousands. The percentage distribution of cloth quality in each type of shirt, and The percentage distribution of dye quality in each type of shirt. What is the ratio of the three qualities of dyes in high quality cloth ?
A 7:9:10
B 1:2:5
C 2:1
D Cannot be determined
when demand for factory's products is high . more money is spent at the factory for safety precautions and machinery maintenance than when demand is low. thus the average number of on -the-job accidents per employee each month should be lower during perids when demand is high than when demand is low and less money is available for safety precautions and machinery maintenance .when demand for its products is high, casts the most serious doubt on the conclusion drawn above?
A Employees demand for higher wages than they do at other times.
B Authority hires new workers but lacks the time to rain them properly.
C Employees are less likely to lose their jobs than are at other times.
D Authority sponsors a monthly safety award for each division in the factory.
When demand for a factory's products is high, more money is spent at the factory for safety precautions and machinery maintenance than demand is low. Thus the average number of on-the-job accidents per employee each month should be bower during periods when demand is high than when demand is low and less money is available for safety precautions and machinery maintenance. Which of the following,if true about a factory when demand for its product is high casts the most serious doubt on the conclusion drawn above?
A Its employees ask for higher wages than they do at other times.
B Its management hires new workers but lacks the time to train them properly.
C Its employees are less likely to lose their jobs than they are at other times.
D Its management sponsors a monthly safety award for each division in the factory.
A and B go cycling in the same direction with speeds of 6 km /hr and 12 km/hr. A car from behind passes them in 9 and 10 seconds respectively . What is the speeds of the car?
A 22 km/hr
B 33 km/hr
C 66 km/hr
D 44 km/hr

Next steps