Related Questions

When a shaft, is subjected to torsion, the shear stress induced in the shaft varies from
A Minimum at the center to maximum at the circumference
B Maximum at the center to minimum at the circumference
C Zero at the center to maximum at the circumference
D Maximum at the center to zero at the circumference
The strain energy stored in a body due to shear stress, is (where $$\tau $$ = Shear stress, C = Shear modulus and V = Volume of the body)
A $$\frac{{\tau {\text{V}}}}{{2{\text{C}}}}$$
B $$\frac{{2{\text{C}}}}{{\tau {\text{V}}}}$$
C $$\frac{{{\tau ^2}{\text{V}}}}{{2{\text{C}}}}$$
D $$\frac{{2{\text{C}}}}{{{\tau ^2}{\text{V}}}}$$
The stress induced in a body, when suddenly loaded, is _________ the stress induced when the same load is applied gradually.
A Equal to
B One-half
C Twice
D Four times
A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is
A $$\frac{{\text{M}}}{{\text{T}}}$$
B $$\frac{{\text{T}}}{{\text{M}}}$$
C $$\frac{{2{\text{M}}}}{{\text{T}}}$$
D $$\frac{{2{\text{T}}}}{{\text{M}}}$$
The stress in the bar when the load is applied suddenly is __________ as compared to the stress induced due to gradually applied loads.
A Same
B Double
C Three times
D Four times
Two shafts A and B are made of the same material. The diameter of shaft A is twice as that of shaft B. The power transmitted by the shaft A will be __________ of shaft B.
A Twice
B Four times
C Eight times
D Sixteen times
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to
A $$\frac{{\text{T}}}{2}$$
B 1T
C 2T
D 4T
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
When a body is subjected to a direct tensile stress ($${\sigma _{\text{x}}}$$) in one plane accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), the maximum shear stress is
A $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{{{\sigma _{\text{x}}}}}{2} - \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
C $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 - 4\tau _{{\text{xy}}}^2} $$
D $$\frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$

Next steps