Bissoy.com
Doctors Medicines MCQs Q&A

Which two of the following commands will place network 10.2.3.0/24 into area 0?
1. router eigrp 10
2. router ospf 10
3. network 10.0.0.0
4. network 10.2.3.0 0.0.0.255 area0
5. network 10.2.3.0 0.0.0.255 area 0

Which two of the following commands will place network 10.2.3.0/24 into area 0?
1. router eigrp 10
2. router ospf 10
3. network 10.0.0.0
4. network 10.2.3.0 0.0.0.255 area0
5. network 10.2.3.0 0.0.0.255 area 0 Correct Answer 2 and 5

To enable OSPF, you must first start OSPF using a Process ID. The number is irrelevant; just choose a number from 1 to 65,535 and you're good to go. After you start the OSPF process, you must configure any network that you want advertised via OSPF using wildcards and the area command. Statement (4) is wrong because there must be a space after the parameter area and before you list the area number.

Related Questions

Which two commands are required for basic OSPF configuration? area ” and “Router ospf ” b) “ area ” and “ area ” c) Only “Router ospf ” d) “ area ” and “Router ospf ”
To enable EIGRP, which of the following would you use?
1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
2. Router1(config-if)# ipv6 router rip 1
3. Router1(config)# ipv6 router eigrp 10
4. Router1(config-rtr)# no shutdown
5. Router1(config-if)# ipv6 eigrp 10
Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
Which of the following describe the process identifier that is used to run OSPF on a router?
1. It is locally significant.
2. It is globally significant.
3. It is needed to identify a unique instance of an OSPF database.
4. It is an optional parameter required only if multiple OSPF processes are running on the router.
What are reasons for creating OSPF in a hierarchical design?
1. To decrease routing overhead
2. To speed up convergence
3. To confine network instability to single areas of the network
4. To make configuring OSPF easier
You are the administrator of a Windows 2000 Server computer. The server contains one network adapter and is a file and print server for critical company resources. You install a second network adpater in the server and connect it to the same network subnet as the first adapter. You want to ensure that the first adapter is used for all network traffic and the second adapter is used only if the first adapter fails or is disconnected from the network. You also want to ensure that the server always has network connectivity even if one network adapter fails. What should you do?
Consider the following statements about the routing protocols. Routing Information Protocol (RIP) and Open Shortest Path First (OSPE) in an IPv4 network. I. RIP uses distance vector routing II. RIP packets are sent using UDP III. OSPF packets are sent using TCP IV. OSPF operation is based on link-state routing Which of the statements above are CORRECT?
Which is true regarding EIGRP successor routes?
1. A successor route is used by EIGRP to forward traffic to a destination.
2. Successor routes are saved in the topology table to be used if the primary route fails.
3. Successor routes are flagged as "active" in the routing table.
4. A successor route may be backed up by a feasible successor route.
5. Successor routes are stored in the neighbor table following the discovery process.
You get a call from a network administrator who tells you that he typed the following into his router:
Router (config) #router ospf 1Router (config-router) #network 10.0.0.0 255.0.0.0 area 0
He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?