EIGRP And OSPF MCQ

Test your knowledge with important EIGRP And OSPF MCQ and their applications. These MCQs are beneficial for competitive exams too. Explore 30+ more EIGRP And OSPF MCQs on Bissoy. Bissoy App

• Which of the following network types have a designated router and a backup designated router assigned?1. Broadcast2. Point-to-point3. NBMA4. NBMA point-to-point
  ক

  1, 2 and 3

  খ

  1 and 3

  গ

  3 and 4

  ঘ

  All of the above
• Which type of OSPF network will elect a backup designated router?<br>1. Broadcast multi-access<br>2. Non-broadcast multi-access<br>3. Point-to-point<br>4. Broadcast multipoint
  ক

  1 and 2

  খ

  3 and 4

  গ

  3 only

  ঘ

  None of the above
• Which of the following network types have a designated router and a backup designated router assigned?<br>1. Broadcast<br>2. Point-to-point<br>3. NBMA<br>4. NBMA point-to-point
  ক

  1, 2 and 3

  খ

  1 and 3

  গ

  3 and 4

  ঘ

  All of the above
• You get a call from a network administrator who tells you that he typed the following into his router:<div class="program-section"><pre><code>Router (config) #router ospf 1Router (config-router) #network 10.0.0.0 255.0.0.0 area 0</code></pre></div>He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?
  ক

  The wildcard mask is incorrect.

  খ

  The OSPF area is wrong.

  গ

  The OSPF Process ID is incorrect.

  ঘ

  The AS configuration is wrong.
• Which of the following protocols support VLSM, summarization, and discontiguous networking?<br>1. RIPv1<br>2. IGRP<br>3. EIGRP<br>4. OSPF<br>5. BGP<br>6. RIPv2
  ক

  1 and 4

  খ

  2 and 5

  গ

  3, 4 and 6

  ঘ

  All of the above
• Which two of the following commands will place network 10.2.3.0/24 into area 0?<br>1. <code class="args"><em>router eigrp 10</em></code><br>2. <code class="args"><em>router ospf 10</em></code><br>3. <code class="args"><em>network 10.0.0.0</em></code><br>4. <code class="args"><em>network 10.2.3.0 0.0.0.255 area0</em></code><br>5. <code class="args"><em>network 10.2.3.0 0.0.0.255 area 0</em></code>
  ক

  1 and 4

  খ

  2, 4, and 5

  গ

  2 and 5

  ঘ

  3 and 4
• What are reasons for creating OSPF in a hierarchical design?<br>1. To decrease routing overhead<br>2. To speed up convergence<br>3. To confine network instability to single areas of the network<br>4. To make configuring OSPF easier
  ক

  1, 2 and 3

  খ

  3 only

  গ

  3 and 4

  ঘ

  2, 3 nd 4
• Which of the following are true regarding OSPF areas?<br>1. You must have separate loopback interfaces configured in each area.<br>2. The numbers you can assign an area go up to 65,535.<br>3. The backbone area is also called area 0.<br>4. If your design is hierarchical, then you don't need multiple areas.<br>5. All areas must connect to area 0.
  ক

  1 only

  খ

  1 and 2 only

  গ

  3 and 4 only

  ঘ

  3, 4 and 5
• Which EIGRP information is held in RAM and maintained through the use of Hello and update packets?<br>1. Neighbor table<br>2. STP table<br>3. Topology table<br>4. DUAL table
  ক

  2 only

  খ

  4 only

  গ

  1 and 3

  ঘ

  All of the above
• Which is true regarding EIGRP successor routes?<br>1. A successor route is used by EIGRP to forward traffic to a destination.<br>2. Successor routes are saved in the topology table to be used if the primary route fails.<br>3. Successor routes are flagged as "active" in the routing table.<br>4. A successor route may be backed up by a feasible successor route.<br>5. Successor routes are stored in the neighbor table following the discovery process.<br>
  ক

  1 and 3

  খ

  2 and 3

  গ

  1 and 4

  ঘ

  3, 4 and 5
• Which command will display all the EIGRP feasible successor routes known to a router?
  ক

  <code class="args"><em>show ip routes *</em></code>

  খ

  <code class="args"><em>show ip eigrp summary</em></code>

  গ

  <code class="args"><em>show ip eigrp topology</em></code>

  ঘ

  <code class="args"><em>show ip eigrp adjacencies</em></code>
• Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?
  ক

  <code class="args"><em>router eigrp 11</em></code>

  খ

  <code class="args"><em>router eigrp 10</em></code>

  গ

  <code class="args"><em>router eigrp 10 redistribute igrp</em></code>

  ঘ

  <code class="args"><em>router igrp combine eigrp 10</em></code>
• A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?
  ক

  IGRP

  খ

  OSPF

  গ

  RIPv1

  ঘ

  EIGRP

  ঙ

  IS-IS
• Which of the following describe the process identifier that is used to run OSPF on a router?<br>1. It is locally significant.<br>2. It is globally significant.<br>3. It is needed to identify a unique instance of an OSPF database.<br>4. It is an optional parameter required only if multiple OSPF processes are running on the router.<br>
  ক

  1, 2 and 4

  খ

  1 and 3

  গ

  3 and 5

  ঘ

  All of the above

  ঙ

  IS-IS