The order in which effort applied to the steering wheel is transferred to the front wheel is

A Steering wheel, Steering gearbox, Steering shaft, Tie rod, Steering knuckle, Front wheels
B Steering wheel, Steering shaft, Steering gearbox, Tie rod, Steering knuckle, Front wheels
C Steering wheel, Steering shaft, Steering gearbox, Steering knuckle, Tie rod, Front wheels
D Steering wheel, Tie rod, Steering gearbox, Steering shaft, Steering knuckle, Front wheels

Correct Answer: Steering wheel, Steering shaft, Steering gearbox, Tie rod, Steering knuckle, Front wheels

Bissoy MCQ
#Automobile Engineering #Automobile Engine

Related Questions

The fundamental equation for correct steering is (where $$\varphi $$ and $$\alpha $$ = Angle through which the axis of the outer wheel and inner wheel turns respectively, c = Distance between the pivots of the front axles and d = Wheel base)
A $$\sin \varphi + \sin \alpha = \frac{{\text{b}}}{{\text{c}}}$$
B $$\cos \varphi - \sin \alpha = \frac{{\text{c}}}{{\text{b}}}$$
C $$\cot \varphi - \cot \alpha = \frac{{\text{c}}}{{\text{b}}}$$
D $$\tan \varphi + \cot \alpha = \frac{{\text{b}}}{{\text{c}}}$$
The Ackerman steering gear mechanism is preferred to the Davis steering gear mechanism, because
A whole of the mechanism in the Ackerman steering gear is on the back of the front wheels and (
B the Ackerman steering gear consists of turning pairs
C the Ackerman steering gear is most economical
D both (a) and (b)
The condition for correct steering of a Davis steering gear is (where $$\alpha = $$  Angle of inclination of the links to the vertical)
A $$\sin \alpha = \frac{{\text{b}}}{{\text{c}}}$$
B $$\cos \alpha = \frac{{\text{c}}}{{\text{b}}}$$
C $$\tan \alpha = \frac{{\text{c}}}{{2{\text{b}}}}$$
D $$\cot \alpha = \frac{{\text{c}}}{{2{\text{b}}}}$$
In a hydraulic power steering system, the power steering pump is driven by a
A Belt driven by camshaft
B Chain driven by crankshaft
C Belt driven by drive-shaft
D Belt driven by crankshaft
In vehicles with tilt steering, the steering column is pivoted in
A Upper bracket
B Lower bracket
C Tilt bracket
D Steering yoke joint
A circular wheel 28 inches in diameter rotates the same number of inches per second as a circular wheel 35 inches in diameter. If the smaller wheel makes x revolutions per second, how many revolutions per minutes does the larger wheel make in terms of x?
A 12x
B 24x
C 36x
D 48x
A wheel that has 6 cogs is meshed with a wheel of 14 cogs. When the smaller wheel has made 21 revolutions the number of revelution made by the larger wheel is --
A 4
B 9
C 12
D 49
A circular wheel 28 inches in diameter rotates (moves) the same number of inches per second as a circular wheel 35 inches in diameter. If the smaller wheel makes x revolutions per second, how many revolutions per minute does the larger wheel make in terms of x?
A 12x
B 48x
C 24x
D 36x
The velocity ratio of a simple wheel and axle with D and d as the diameters of effort wheel and load axle, is
A D + d
B D - d
C D × d
D $$\frac{{\text{D}}}{{\text{d}}}$$
During a service recovery effort, the employee was very empathetic to the customer’s plight and agreed to replace the defective product. However, it took three months for the replacement product to show up which was much later than the customer had anticipated. As a result, the recovery effort violated the customer’s ___________ justice need.
A social
B procedural
C interactional
D distributive

Next steps