Bissoy.com
Doctors Medicines MCQs Q&A

In a hydraulic power steering system, the power steering pump is driven by a

In a hydraulic power steering system, the power steering pump is driven by a Correct Answer Belt driven by crankshaft

In a hydraulic power steering system, the power steering pump is driven by a Belt driven by crankshaft

Related Questions

একটি পানিপূর্ণ কুয়ার গভীরতা 20m ও ব্যাস 2 m. কুয়াটিকে পানি শূণ্য করার জন্য 5 HP এর একটি পাম্প লাগানো হল। অর্ধেক পানি তোলার পর পাম্পটি নষ্ট হয়ে গেল। বাকি পানি তোলার জন্য একই ক্ষমতা সম্পন্ন আর একটি পাম্প লাগানো হল। প্রথম পাম্প দ্বারা সম্পাদিত কাজের পরিমান নির্ণয় কর।(The depth and diameter of a water filled well are 20 m and 2 m respectively. An engine of 5 HP is attached to pump out the water. The pump was ruined after emptying half of the water. Then another pump of same capacity was attached to pump out rest of the water. Determine the work done by first pump.) 
A, B and C are three small pumps fitted to a tank. D is a large pump fitted to the tank. Pump B is 25% more efficient than A. Pump C is 20% more efficient than B. Pump D is 4/3rd efficient of pump C. All of the pumps are used to fill the tank. What is the ratio of the time taken by pumps A and B to fill the tank together to the time taken by the pumps B and D to fill the tank together?
P. A weir is a hydraulic structure where majority or the entire ponding is achieved by a raised crest and smaller part or nil part by the shutters. Q. A weir is a hydraulic structure that is made by constructing the width of the channel only. R. A barrage is a hydraulic structure that is made by creating a choking condition only. S. A barrage is a hydraulic structure where majority or the entire ponding is achieved by a shutter and smaller part or nil part by the raised crest. Identify the correct statements in the above.
A centrifugal pump which circulates a hot liquid metal at 500 degree Celsius is driven by a 3600 rpm electric motor. The motor is coupled to the pump impeller by a horizontal steel shaft of dia 25 mm. Let us assume the motor temperature as 60 degree Celsius with the ambient air at 25 degree Celsius, what length of shaft should be specified between the motor and the pump? It may be presumed that the thermal conductivity of the shaft material is 35W/m K and that the convective film coefficient between the steel shaft and the ambient air is 15.7W/square m K
Working alone, pump A can empty a pool in 3 hours. Working alone, pump B can empty the same pool in 2 hours. Working together, how many minutes will it take pump A and pump B to empty the pool?
A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump
In the question below are given two statements followed by two conclusions numbered I and II. You have to take the given statements to be true even if they seem to be at variance with commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: I. Only a few generator is pump II. Some pump is gasoline Conclusions: I. Some pump is not gasoline II. Some generator is not pump
If the gear ratio for fuel pump is thrice that of the oxidizer pump, the shaft speed of fuel pump is ____________ the oxidizer pump.
A car averages 25 miles per gallon of gasoline when driven in the city and 40 miles per gallon when driven on the highway. According to these rates, which of the following is closest to the number of miles per gallon that the car averages when it is driven 10 miles in the city and then 50 miles on the highway?
A car averages 25 miles per gallon of gasoline when driven in the city and 40 miles per gallon when driven on the highway. According to these rates, which of the following is closest to the number of miles per gallon that the car average when it is driven 10 miles in the city and then 60 miles on the highway?