Bissoy.com
Doctors Medicines MCQs Q&A

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding.

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. Correct Answer 1.34

Related Questions

The critical reasoning question is based on a short argument, a set of statements, or a plan of action. For each question, select the best answer of the choices given. The size of particles is directly linked to their potential for causing health problems. Small particles less than 10 micrometers in diameter cause the greatest problems, as they can get deep into the lungs and some may get into the bloodstream. One being exposed to such particles can affect both the lungs and the heart of a person. But there are particles that are causing environmental effects too, few of which are given below.  Which among the following below options does not talk about the effects of these particles on the environment?
In a laboratory test run, the rate of drying was found to be 0.5 × 10-3 kg/m2.s, when the moisture content reduced from 0.4 to 0.1 on dry basis. The critical moisture content of the material is 0.08 on a dry basis. A tray dryer is used to dry 100 kg (dry basis) of the same material under identical conditions. The surface area of the material is 0.04 m2/kg of dry solid. The time required (in seconds) to reduce the moisture content of the solids from 0.3 to 0.2 (dry basis) is
The energy required per unit mass to grind limestone particles of very large size to 100 μm is 12.7 kWh/ton. An estimate (using Bond's law) of the energy to grind the particles from a very large size to 50 μrn is
Consider the following statements regarding clutches 1. Dry clutch has higher coefficient of friction compared to wet clutch 2. The torque capacity of wet clutch is high compared to dry clutch. 3. The engagement in a dry clutch is smoother than in case of wet clutch. Which of the above statements is/are correct ?
The value of work index does not change materially from one equipment to another. If the value of work index determined for close circuit grinding is Wi, then the same for open circuit grinding will be
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
A set of jobs A, B, C, D, E, F, G, H arrive at time t = 0 for processing on turning and grinding machines. Each job needs to be processed in sequence - first on the turning machine and second on the grinding machine, and the grinding must occur immediately after turning. The processing times of the jobs are given below. Job A B C D E F G H Turning (minutes) 2 4 8 9 7 6 5 10  Grinding (minutes)  6 1 3 7 9 5 2 4 If the makespan is to be minimized, then the optimal sequence in which these jobs must be processed on the turning and grinding machines is
In the following question, the first and the last part of the sentence/passage are numbered 1 and 6. The rest of the sentence/passage is split into four parts and named P, Q, R, S. These four parts are not given in their proper order. Read the sentence/passage and find out which of the four combinations is correct. S1. Energy conservation refers to the efforts made to reduce the consumption of energy. P. Furthermore, energy can take plenty of time to regenerate. Q. The energy on Earth is not in unlimited supply. R. Most noteworthy, energy conservation is achievable either by using energy more efficiently or by reducing the amount of service usage. S. This certainly makes it essential to conserve energy.  S6. Energy conservation will reduce the expenses related to fossil fuels.
The size of the philips LCD television screen is given as the length of the screen's diagonal , Assume that the screens of the television were flat. Find out how many square inches greater would be the screen of square inches greater would be the screen of a square 21 -inch television set than that of a square 19-inch television set.
The size of the Philips LCD television screen is given as the length of the screen's diagonal, Assume that the screen of the television were flat, Find out how many square inches greater would be the screen of a square 21-inch television st than that of a square 19-inch television set