Related Questions

Rashna Company collected the following data in its accounting records in 2014 : From the income statement : Depreciation expense Tk. 1,000 Loss on sale of equipment 3,000 From the comparative balance sheet : Beginning balance , equipment Tk. 12,500 Ending balance , equipment 8,000 Beginning balance , accumulated depreciation 2,000 Ending balance , accumulated depreciation 2,400 No new equipment was purchased during the year. The equipment was sold at the end of the year. What was the cash in -flow from the sale of equipment in 2014?
A Tk, 3,900
B Tk. 1,000
C Tk. 900
D Tk. 600
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If Z is open, which of the following must be true?
A S is open
B T is open
C U is open
D y is open
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If R is closed and U is open, which of the following must be true?
A S is open
B T is open
C T is closed
D Y is closed
In closed circuit grinding as compared to open circuit grinding, the
A Specific surface of product is more
B Product has lesser size uniformity
C Production rate at a given limiting size is lower
D Operation is economical
Grinding wheel made of silicon carbide is most suitable for grinding materials of low tensile strength (e.g; tough bronze). Grinding is a __________ operation.
A Turning
B Dressing
C Forming
D Surface finishing
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If the maximum number of valves that can be closed at the same time are closed which of the following must true?
A R is open
B S is open
C T is open
D Z is open
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. Which of the following, if given to the mixing vat operator as an instruction, would not determine the setting of any other valve ?
A S must be open
B T must be open
C U must be open
Close circuit grinding by a ball mill with air sweeping employs a
A Classifier
B Cyclone separator between mill & classifier
C Both A & B
D Neither A nor B
A. __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end.
A Compartment
B Tube
C Rod
D Pebble
A fine grained grinding wheel should not be used for grinding __________ materials.
A Hard
B Brittle
C Soft & ductile
D None of these

Next steps