Bissoy.com
Doctors Medicines MCQs Q&A

An ammeter has an internal resistance of 50 Ω. The meter movement itself can handle up to 1 mA. If 10 mA is applied to the meter, the shunt resistor, RSH1, is approximately

An ammeter has an internal resistance of 50 Ω. The meter movement itself can handle up to 1 mA. If 10 mA is applied to the meter, the shunt resistor, RSH1, is approximately Correct Answer 5.5 Ω

Related Questions

A resistance R is measured using the connection shown in the below figure. The current measured is 10 A on ranges 100A and the voltage measured is 125 V on 150 V range. The scales of the ammeter and voltmeter are uniform. The total number of scale divisions of the ammeter is 100 and that of the voltmeter is 150. The scale division can be distinguished. The constructional error of the ammeter is ± 0.3% and that of voltmeter±0.4%. The resistance of the ammeter is 0.25 Ω. The possible error in the measurement of R is?
A 100KW, 250 V, 400 A, a long shunt compound generator has an armature resistance of 0.025 ohms. There are 1000 shunt fields turns per pole and 3 series field turns per pole. The series field is connected in a such a fashion that positive armature current produces direct-axis MMF which adds to that of the shunt field. Compute the gross MMF at the rated terminal current when shunt field current is 4.7A and speed is 1150 rpm.
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip
The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100 ohms. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?
সিরিজে সংযুক্ত একটি এ্যামিটার এবং একটি অজানা রোধ দুটি একই রকম 1.5 V ব্যাটারীর দুই প্রান্তে সংযুক্ত আছে। যখন ব্যাটারী দুটি সিরিজে সংযুক্ত থাকে তখন এ্যামিটার। amp রিডিং প্রদর্শন করে। আবার ব্যাটারী দুটি সমান্তরালে সংযুক্ত করলে 0.6 amp রিডিং প্রদর্শন করে। ব্যাটারীর আভ্যন্তরিন রোধ কত ? (An ammeter and an unknown resistance are connected in series across two identical batteries of each 1.5 V. The ammeter shows current I amp and 0.6 amp when the batteries are connected in series and parallel, respectively. What is the internal resistance of the battery?)
A permanent magnet moving coil ammeter has a coil resistance of 99ohm and Full Scale DeflectionFSD. current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is
A galvanometer of internal resistance 5 Ω has range 2 amps. In order to convert it into an ammeter of range 10 amps, how much shunt resistance is required?
The parallel combination of a 6.8 kΩ resistor and a 10 kΩ resistor is in series with the parallel combination of a 2.2 kΩ resistor and a 1 kΩ resistor. A 100 V source is connected across the circuit. The resistor(s) with the greatest voltage drop is (are)
A 12 kΩ resistor, a 15 kΩ resistor, and a 22 kΩ resistor are in series with two 10 kΩ resistors that are in parallel. The source voltage is 75 V. Current through the 15 kΩ resistor is approximately
Which Statements is / are correct ? A. An ammeter is connected in series in a circuit and a voltmeter is connected in Parallel. B. An ammeter has a high resistance C. A voltmeter has a low resistance