Related Questions

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge
A Is increased by $$\frac{{{\text{PZ}}}}{{\text{e}}}$$
B Is increased by $$\frac{{{\text{Pe}}}}{{\text{Z}}}$$
C Is decreased by $$\frac{{{\text{Pe}}}}{{\text{Z}}}$$
D Remains unchanged
‘P’ is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is ‘A’ and sectional modulus is ‘Z’. The minimum stress ‘f’ on the beam subjected to a maximum bending moment ‘M’ is
A $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{Z}}}{{\text{M}}}$$
B $${\text{f}} = \frac{{\text{A}}}{{\text{P}}} - \frac{{\text{M}}}{{\text{Z}}}$$
C $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{\text{Z}}}$$
D $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{6{\text{Z}}}}$$
‘P’ is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is ‘A’ and sectional modulus is ‘Z’. The maximum stress ‘f’ in the beam, subjected to a maximum bending moment ‘M’, is
A $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{Z}}}{{\text{M}}}$$
B $${\text{f}} = \frac{{\text{A}}}{{\text{P}}} - \frac{{\text{M}}}{{\text{Z}}}$$
C $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{\text{Z}}}$$
D $${\text{f}} = \frac{{\text{P}}}{{\text{A}}} - \frac{{\text{M}}}{{6{\text{Z}}}}$$
The change in length due to a tensile or compressive force acting on a body is given by (where P = Tensile or compressive force acting on the body, $$l$$ = Original length of the body, A = Cross-sectional area of the body and E = Young's modulus for the material of the body)
A $$\frac{{{\text{P}}l{\text{A}}}}{{\text{E}}}$$
B $$\frac{{{\text{P}}l}}{{{\text{AE}}}}$$
C $$\frac{{\text{E}}}{{{\text{P}}l{\text{A}}}}$$
D $$\frac{{{\text{AE}}}}{{{\text{P}}l}}$$
The ratio of maximum shear stress developed in a rectangular beam and a circular beam of the same cross-sectional area is
A $$\frac{2}{3}$$
B $$\frac{3}{4}$$
C 1
D $$\frac{9}{8}$$
If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be.
A Straight below centroidal axis
B Parabolic with convexity downward
C Parabolic with convexity upward
D Straight above centroidal axis
The rectangular beam 'A' has length ‘l’, width ‘b’ and depth ‘d’. Another beam 'B' has the same length and depth but width is double that of 'A'. The elastic strength of beam 'B' will be _________ as compared to beam ‘A’.
A Same
B Double
C Four times
D Six times
The rectangular beam 'A ' has length l, width b and depth d. Another beam 'B' has the same width and depth but length is double that of 'A'. The elastic strength of beam 'B' will be __________ as compared to beam A.
A Same
B One-half
C One-fourth
D One-eighth
The rectangular beam 'A' has length l, width b and depth d. Another beam 'B' has the same length and width but depth is double that of 'A'. The elastic strength of beam B will be __________ as compared to beam A.
A Same
B Double
C Four times
D Six times
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these

Next steps