Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A resistance R is measured using the connection shown in the below figure. The current measured is 10 A on ranges 100A and the voltage measured is 125 V on 150 V range. The scales of the ammeter and voltmeter are uniform. The total number of scale divisions of the ammeter is 100 and that of the voltmeter is 150. The scale division can be distinguished. The constructional error of the ammeter is ± 0.3% and that of voltmeter±0.4%. The resistance of the ammeter is 0.25 Ω. The possible error in the measurement of R is?
Consider the following statement: 1. Initial load tests and routine load tests are carried out on test piles and working Piles, respectively. 2. In a pile load test, the allowable load can be taken equal to half the ultimate load at which the total settlement amounts to one-tenth of the pile diameter. 3. In a pile load test, the allowable load can be taken equal to two-thirds of the total toad which causes a plastic settlement of 6 mm. Which of the above statements are correct?
While measuring power observed by the load using the arrangement shown in the figure, the obtained values voltmeter and ammeter readings are 150 V and 12 A respectively. If the load power factor is unity, the wattmeter reading will be- (the internal resistances of instruments are mentioned in the figure).
Which of the following statements are true? a. As load increases armature current decreases, regardless of excitation. b. For under and over excited motors, power factor tends to approach zero with increase in load c. With normal excitation when load is increased, change in armature current is greater than in power factor which tends to become increasingly leading. d. Both with under and over excitation, change in power factor is greater than in armature current with increase in load.
A – 3 phase balanced load which has a power factor of 0.707 is connected to balanced supply. The power consumed by the load is 5 kW. The power is measured by the two-wattmeter method. The readings of the two watt meters are.
An ammeter has a resistance of G ohms and range of I amperes. The value of resistance required in parallel to convert it into an ammeter of range nI is ___________.
সিরিজে সংযুক্ত একটি এ্যামিটার এবং একটি অজানা রোধ দুটি একই রকম 1.5 V ব্যাটারীর দুই প্রান্তে সংযুক্ত আছে। যখন ব্যাটারী দুটি সিরিজে সংযুক্ত থাকে তখন এ্যামিটার। amp রিডিং প্রদর্শন করে। আবার ব্যাটারী দুটি সমান্তরালে সংযুক্ত করলে 0.6 amp রিডিং প্রদর্শন করে। ব্যাটারীর আভ্যন্তরিন রোধ কত ? (An ammeter and an unknown resistance are connected in series across two identical batteries of each 1.5 V. The ammeter shows current I amp and 0.6 amp when the batteries are connected in series and parallel, respectively. What is the internal resistance of the battery?)
Which Statements is / are correct ? A. An ammeter is connected in series in a circuit and a voltmeter is connected in Parallel. B. An ammeter has a high resistance C. A voltmeter has a low resistance
Consider the following statements regarding reciprocity theorem : 1. In any passive linear bilateral network, if the single voltage source Vx, in branch x produces the current response Iy, in branch y, then the removal of the voltage source from branch x and its insertion in branch y will produce the current response iy in branch x. 2. The interchange of an ideal voltage source and an ideal ammeter in any passive, linear, bilateral circuit will not change the ammeter reading. 3. The interchange of an ideal current source and an ideal voltmeter in any passive linear bilateral circuit will change the voltmeter reading. Which of the above statements are correct ?
In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed