You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?

A show ip eigrp adjacency
B show ip eigrp topology
C show ip eigrp interfaces
D show ip eigrp neighbors

Correct Answer: show ip eigrp neighbors

The show ip eigrp neighbors command allows you to check the IP addresses as well as the retransmit  interval and queue counts for the neighbors that have established an adjacency.

Bissoy MCQ
#CCNA #CISCO Certification

Related Questions

You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?
A show running-config
B show startup-config
C show interfaces
D show protocols
You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
A You didn
B NVRAM is corrupted.
C The configuration register setting is incorrect.
D The newly upgraded IOS is not compatible with the hardware of the router.
You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?
A Router (config-if) #encapsulation frame-relay q933a
B Router (config - if) #encapsulation frame-relay ansi
C Router (config - if) #encapsulation frame-relay ietf
D Router (config - if) #encapsulation frame-relay cisco
The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?
A RAM should be erased and the router restarted
B Flash should be erased and the router restarted
C NVRAM should be erased and the router restarted
D The new configuration should be entered and saved
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
A The Lowest IP address of any physical interface
B The Highest IP address of any physical interface
C The Lowest IP address of any logical interface
D The Highest IP address of any logical interface
The Token-Ring architecture was developed for a more efficient way to determine who should be transmitting at any one time. With Ethernet, collisions may take place, causing the transmitting computers to have to retransmit their data. The use of token guarantees that only one computer can transmit at a time. What happens as the network increases in size? Choose the best answer
A An additional token is added for every 1,000 nodes
B The speed of the Token-Ring network must be 16Mbps if the number of nodes is greater then 500
C The network becomes less efficient
D After the number of nodes exceeds 550, the Multistation Access Unit must be replaced by the more powerful Hyperstation Unified Bandwidth device
E The network becomes more efficient
Which command will display the CHAP authentication process as it occurs between two routers in the network?
A show chap authentication
B show interface serial 0
C debug ppp authentication
D debug chap authentication
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
A The updated information will be added to the existing routing table Debug IP rip
B The update will be ignored and no further action will occur Debug IP route
C The updated information will replace the existing routing table entry
D The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence
A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?
A show version
B show flash
C show memory
D show buffers
Which command will display all the EIGRP feasible successor routes known to a router?
A show ip routes *
B show ip eigrp summary
C show ip eigrp topology
D show ip eigrp adjacencies

Next steps