Bissoy.com
Doctors Medicines MCQs Q&A

In butt weld joint, what will be the strength equation? if the thickness of the plate is t, permissible tensile stress for the weld is σt, and the length of the weld is l.

In butt weld joint, what will be the strength equation? if the thickness of the plate is t, permissible tensile stress for the weld is σt, and the length of the weld is l. Correct Answer σttl

In butt joints, the tensile force is observed. The strength of the butt joint is a product of the area resisting the tensile stress and the permissible tensile stress for the weld is σt.

Related Questions

The tensile strength of the welded joint for double fillet is (where s = Leg or size of the weld, $$l$$ = Length of weld and $${\sigma _{\text{t}}}$$ = Allowable tensile stress for weld metal)
With reference to the following figure, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.
In a rivet joint thickness of the plate is t and the length of the margin is m. If the permissible shearing stress of the plate is τs, find the shear strength of the joint at the margin.
Two plates of 12mm and 16mm thickness are to be joined by groove weld. The joint is subjected to factored tensile load of 400kN. Due to some reasons the effective length of weld that could be provided was 150mm only. What is the safety of joint if single-V groove weld is provided?
Which of the following statements are correct in respect of welded connections? 1) Strength of Butt weld is equal to the strength of components joined. 2) Fillet welds carry the loads computed based on the tensile strength characteristics of fusion material. 3. for effective transmission of load by fillet weld, the fusion faces shall subtend an angle between 60° and 120° 
A flat plate 30mm wide and “t”mm wide is subjected to a tensile force of 5kN. The plate has a circular hole of diameter 15mm with the centre coinciding with the diagonal intersection point of the rectangle. If stress concentration factor=2.16, find the thickness of the plate if maximum allowable tensile stress is 80N/mm².
A fillet-welded joint is subjected to transverse loading F as shown in the figure. Both legs of the fillets are of 10 mm size and the weld length is 30 mm. If the allowable shear stress of the weld is 94 MPa, considering the minimum throat area of the weld, the maximum allowable transverse load per weld in kN is
For the plate of thickness t, which is in tension has permissible stress of σt, with pitch p, and rivet hole diameter d, find the tensile strength of the riveted joint.
In the consumable electrode shielded metal arc welding process, which of the following observations are correct?
P. The, weld composition does not depend upon the basicity of the slag.
Q. Basic flux is used to achieve low hydrogen content-and low inclusion content in the weld metal.
R. Reverse polarity of the direct current power source is used to weld thin sheets.
S. Coated electrodes are classified by tensile strength of the weld metal deposit.
Calculate ultimate moment and shear of effective span is 30m, live load is 9kn/m, dead load excluding self weight is 2kn/m, load factors for dead load is 1.4 for live load is 1.6 cube strength of concrete fcu is 50n/mm2 cube strength at transfer is fci is 35n/mm2, tensile strength of concrete Ec is 34kn/mm2 loss ratio ɳ is 0.85 and 8mm diameter high tensile strength fpu is 1500n/mm2 are available for use and the modulus of elasticity of high tensile wires is 200kn/mm2?