Bissoy.com
Doctors Medicines MCQs Q&A

A countershaft of engineering workshop is driven by electric motor with the help of canvas belt and pulley arrangement such that the speed of bet is 600 m/min and it transmits 50 KW. Find the difference between tension on either side of the belt.

A countershaft of engineering workshop is driven by electric motor with the help of canvas belt and pulley arrangement such that the speed of bet is 600 m/min and it transmits 50 KW. Find the difference between tension on either side of the belt. Correct Answer 5 KN

P = (T1 – T2) * v 50 * 1000 = (T1 – T2) * 10 T1 – T2 = 5 KN.

Related Questions

A counter shaft of engineering workshop is being driven by electric motor with the help of canvas belt and pulley arrangement such that the speed of belt is 600 m/min and it transmits 50 KW. What will be the difference between tensions on either side of the belt?
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. Calculate the tension in the rope of pulley C.
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.
Power is transmitted by an electric motor to a machine by using a belt drive. The tensions on the tight and slack side of the belt are 2200 N and 1000 N respectively and diameter of the pulley is 600 mm. If speed of the motor is 1500 r.p.m, find the power transmitted.
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. If bending moment on point B in horizontal plate is M and in vertical plane is m, then the net bending moment at point B is?
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. Calculate the torque supplied to the shaft.
According to the International Commission on Education for the Twenty-first Century headed by Jacques Delors, which of the following main tensions will be witnessed during the 21st century ? A. The tension between the global and the local B. The tension between tradition and modernity C. The tension between the spiritual and the material D. The tension between the poor and the rich E. The tension between the developed and the developing societies Choose the correct answer from the options given below:
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
An electric motor drives a machine through a speed reducing gear of ratio 9:1. The motor armature, with its shaft and gear wheel, has moment of inertia 0.6 kg-m2. The rotating part of the driven machine has moment of inertia 45 kg-m2. The driven machine has resisting torque of 100 N-m and the efficiency of reduction gear is 95%. Find the power which the motor must develop to drive the machine at a uniform speed of 160 r.p.m.