Bissoy.com
Doctors Medicines MCQs Q&A

Refer to Q3 and Q4 and estimate what is the maximum rate at which heat must be removed by the cooling coil (kcal/min) and at what time does this maximum occur? Using the following equation: Q ̇ = ΔHR kc2Ao VR

Refer to Q3 and Q4 and estimate what is the maximum rate at which heat must be removed by the cooling coil (kcal/min) and at what time does this maximum occur? Using the following equation: Q ̇ = ΔHR kc2Ao VR Correct Answer −828 kcal/min

The right-hand side is a maximum in absolute value (note it is a negative quantity) when cA is a maximum, which occurs for cA = cAo, giving Qmax = ΔHR kc2Ao VR = (−10 kcal/mol A) (0.01725 L/mol•min) (2.0 mol/L )2 (1200 L) = −828 kcal/min.

Related Questions

Refer to Q3, and estimate what is the total amount of heat (kcal) that must be removed by the cooling coil when this conversion is reached? Using the following equation: Q ̇= ΔHR r VR
The bypass factor, in case of sensible cooling of air, is given by (where td₁ = Dry bulb temperature of air entering the cooling coil, td₂ = Dry bulb temperature of air leaving the cooling coil, and td₃ = Dry bulb temperature of the cooling coil)
The bypass factor, in case of sensible cooling of air, is given by (where td1 = Dry bulb temperature of air entering the cooling coil, td2 = Dry bulb temperature of air leaving the cooling coil and td3 = Dry bulb temperature of the cooling coil)
Concentrated fermentation liquid containing 20% (w/w) gluconic acid from an evaporator has a flow rate of 2000 kg/h and a temperature 90 °C. It needs to be cooled to 6 °C in a heat exchanger with cooling water. The cooling water has a flow rate 2700 kg/h and an initial temperature 2 °C. If the cooling water leaves the heat exchanger at 50 °C, what is the rate of heat loss from gluconic acid solution to the surroundings? Assume the heat capacity of gluconic acid is 0.35 cal/g-°C-1.
Consider the following statements for cooling towers: 1. Cooling tower is an artificial device used to cool the hot cooling water coming out of condenser more effectively. 2. The amount of water usually lost with induced draft cooling tower ranges from 5% to 6% by evaporation. 3. The amount of water usually lost with induced draft cooling tower ranges from 7% to 8% by drift losses. 4. The rate of evaporation of water and its cooling effect on the remaining water depends upon the relative humidity of air passing through the tower. Which of the above statements are correct?
A solid-oxide fuel cell is fed with carbon monoxide and reacts with air to produce CO2. This reaction will produce 2 electrons which are used to power an electric circuit external to the fuel cell. The reaction equation is shown below: 2CO(g) + O2(g) -> 2CO2(g) ΔHr° = -565.96 kJ/mol This reaction does not occur for other types of fuel cells which use a catalyst, such as polymerelectrolyte membrane or phosphoric-acid fuel cells. The presence of carbon monoxide on the anode side of these types of fuel cells will cause catalyst poisoning, reducing the efficiency and voltage of the fuel cell. Determine the rate of enthalpy change for a carbon dioxide production rate of 208 mol/hr. The extent of the reaction occurring in the fuel cell can be obtained by the following equation: where:
Which of the following statements are true/false?
1. A minimum rate of wages for the time spent by employees for the production of output is minimum time rate.
2. Minimum piece rate is the rate based on the quantity of the output employees have produced.
3. The guaranteed time rate is a minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis.
4. A minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis is overtime rate.
Match the column. a. Detailed estimate 1. Estimate of additional works during the process b. Supplementary estimate 2. Prepared for approx. rates initially c. Revised estimate 3. Includes details and cost of everything d. Rough estimate 4. Prepared when the costs exceed more than 5%
What is the correct sequence of preparing an estimate? 1. Detailed estimate 2. Approximate estimate 3. Supplementary estimate 4. Revised estimate
The sensible heat factor during cooling and dehumidification process is given by (where h₁ = Enthalpy of air entering the cooling coil, h₂ = Enthalpy of air leaving the cooling coil, and hA = Enthalpy of air at the end of dehumidification process)