Bissoy.com
Doctors Medicines MCQs Q&A

The residual stress in the material after metalworking can be detected by which of the following method?

The residual stress in the material after metalworking can be detected by which of the following method? Correct Answer X-ray analysis

The residual stress in the material is determined by X-ray analysis. The concept is that the lattice spacing of the material changes with change in residual stress of the material, so the corresponding diffraction pattern changes.

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
Which of the following statements are correct? 1. Stress Isobar can be prepared using Boussinesq’s stress distribution theory. 2. Equivalent point load method yields accurate results. 3. Newmark’s method relates the vertical stress with the help of influence chart. 4. Westergaard’s method helps in determination of stress distribution for layered soils. Select the correct answer using the codes given below:
In this question, a passage and a related statement have been given. Read the passage carefully and assess the statement based on it. Using knives and screws, two Russian astronauts on Tuesday took a sample of substance around a mysterious cavity of the spacecraft called the Soyuz, which was placed in the International Space Station, a Moscow official suggested that it was a break - It can also be done. In August, two months after the last visit of the vehicle, the air leak was detected in the Soyuz spacecraft due to the 2 mm air in the ISS. Roskosmos, an astronomical institute, says that cutting off the insulation on the hole and sampling the material around it and the purpose of putting a new insulation on it is to find out that this small but dangerous hole has been done on earth or Is in space. The chief of Roskosmos has said that the error of manufacturing has not been found in the investigation. Experienced astronauts had to struggle but they managed their mission. Before the spacewalk, astronauts were able to inspect the hole just from within the spacecraft. The biggest difficulty was that in the Soyuz spacecraft, the ISS was not designed to improve during adverse weather space, and no railing was also made to catch the space passengers outside the vehicle. Statement: In the Soyuz spacecraft, the air leak due to the presence of the leak was detected after two months of the last visit. Select the appropriate from the given options A - Statement is completely true B - The statement is possibly true C - the statement can not be determined D - Statement is completely false
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
An axial residual compressive stress due to a manufacturing process is present on the outer surface of a rotating shaft subjected to bending. Under a given bending load, the fatigue of the shaft in the presence of the residual compressive stress is ____________
In the metalworking process, the stress, in the range as shown by engineering stress-strain curve is _______
The maximum value, which the residual stress in a material can reach is the __________ of the material.
Consider the following statements: 1. The working stress design is based on explicit consideration of the various conditions under which the structure may cease to fulfill its intended function. 2. In the case of working stress design, the structure will directly take into consideration the various relevant modes of failure. 3. In the working stress method, regulatory bodies or classification societies usually specify the value of the allowable stress as some fraction of the mechanical properties of materials Which of the above statements is/are correct?