Bissoy.com
Doctors Medicines MCQs Q&A

Atmospheric air at 30 degree Celsius temperature and free stream velocity of 2.5 m/s flows along the length of a flat plate maintained at a uniform surface temperature of 90 degree Celsius. Let length = 100 cm, width = 50 cm and thickness = 2.5 cm. Thermal conductivity of the plate material is 25 W/m K, find heat lost by the plate

Atmospheric air at 30 degree Celsius temperature and free stream velocity of 2.5 m/s flows along the length of a flat plate maintained at a uniform surface temperature of 90 degree Celsius. Let length = 100 cm, width = 50 cm and thickness = 2.5 cm. Thermal conductivity of the plate material is 25 W/m K, find heat lost by the plate Correct Answer 185.88 W

Q = h A d t where, Nu = h l/k. So, Q = 185.88 W.

Related Questions

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Air at 20 degree Celsius flows over a flat plate maintained at 75 degree Celsius. Measurements shows that temperature at a distance of 0.5 mm from the surface of plate is 50 degree Celsius. Presuming thermal conductivity of air is 0.0266 W/m K, estimate the value of local heat transfer coefficient
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
A small thermo-couple is positioned in a thermal boundary layer near a flat plate past which water flows at 30 degree Celsius and 0.15 m/s. The plate is heated to a surface temperature of 50 degree Celsius and at the location of the probe, the thickness of thermal boundary layer is 15 mm. If the temperature profile as measured by the probe is well-represented by t – t S/t INFINITY – t S = 1.5 (y/δ t) – 0.5 (y/δ t) 3 Determine the heat flux from plate to water
Air at 20 degree Celsius flows over a flat surface maintained at 80 degree Celsius. The local heat flow at a point was measured as 1250 W/m2 .Take thermal conductivity of air as 0.028 W/m K, calculate the temperature at a distance 0.5 mm from the surface
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Ambient air at 20 degree Celsius flows past a flat plate with a sharp leading edge at 3 m/s. The plate is heated uniformly throughout its entire length and is maintained at a surface temperature of 40 degree Celsius. Calculate the thickness of the thermal boundary layer. Assume that transition occurs at a critical Reynolds number of 500000
Air at 20 degree Celsius flows over a flat surface maintained at 80 degree Celsius. Estimate the value of local heat transfer coefficient if the local heat flow at a point was measured as 1250 W/m2. Take thermal conductivity of air as 0.028 W/m K
The handle of a saucepan, 30 cm long and 2 cm in diameter, is subjected to 100 degree Celsius temperature during a certain cooking operation. The average unit surface conductance over the handle surface is 7.35 W/m2 degree in the kitchen air at 24 degree Celsius. The cook is likely to grasp the last 10 cm of the handle and hence the temperature in this region should not exceed 38 degree Celsius. What should be the thermal conductivity of the handle material to accomplish it? The handle may be treated as a fin insulated at the tip