Bissoy.com
Doctors Medicines MCQs Q&A

Air at 20 degree Celsius flows over a flat surface maintained at 80 degree Celsius. The local heat flow at a point was measured as 1250 W/m2 .Take thermal conductivity of air as 0.028 W/m K, calculate the temperature at a distance 0.5 mm from the surface

Air at 20 degree Celsius flows over a flat surface maintained at 80 degree Celsius. The local heat flow at a point was measured as 1250 W/m2 .Take thermal conductivity of air as 0.028 W/m K, calculate the temperature at a distance 0.5 mm from the surface Correct Answer 57.682 degree celsius

Temperature at 0.5 mm from the surface is 80 + (d t/d y) y = 0 (0.0005) = 57.682 degree celsius.

Related Questions

Air at 20 degree Celsius flows over a flat surface maintained at 80 degree Celsius. Estimate the value of local heat transfer coefficient if the local heat flow at a point was measured as 1250 W/m2. Take thermal conductivity of air as 0.028 W/m K
Air at 20 degree Celsius flows over a flat plate maintained at 75 degree Celsius. Measurements shows that temperature at a distance of 0.5 mm from the surface of plate is 50 degree Celsius. Presuming thermal conductivity of air is 0.0266 W/m K, estimate the value of local heat transfer coefficient
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
An average convective heat transfer coefficient for flow of air over a sphere has been measured by observing the temperature-time history of a 12 mm diameter copper sphere (density = 9000 kg/m3 and c = 0.4 k J/kg K) exposed to air at 30 degree Celsius. The temperature of the sphere was measured by two thermocouples one located at the center and the other near the surface. The initial temperature of the ball was 75 degree Celsius and it decreased by 10 degree Celsius in 1.2 minutes. Find the heat transfer coefficient
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree
Two rods A and B of the same length and diameter protrude from a surface at 120 degree Celsius and are exposed at air at 25 degree Celsius. The temperatures measured at the end of the rods are 50 degree Celsius and 75 degree Celsius. If thermal conductivity of material A is 20W/ m K, calculate it for B
Atmospheric air at 30 degree Celsius temperature and free stream velocity of 2.5 m/s flows along the length of a flat plate maintained at a uniform surface temperature of 90 degree Celsius. Let length = 100 cm, width = 50 cm and thickness = 2.5 cm. Thermal conductivity of the plate material is 25 W/m K, find heat lost by the plate
The lubricating oil for a large industrial gas turbine engine is cooled in a counter flow, concentric tube heat exchanger. The cooling water flows through the inner tube ( diameter = 25 mm) with inlet temperature 25 degree celsius and mass flow rate 0.2 kg/s. The oil flows through the annulus (diameter = 50 mm) with mass flow rate 0.125 kg/s and its temperature at entry and exit are 90 degree Celsius and 60 degree Celsius. Find outlet temperature of cooling water
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K