Bissoy.com
Doctors Medicines MCQs Q&A

An iron billet (k = 65 W/m K) measuring 20 * 15 * 80 cm is exposed to a convective flow resulting in convection coefficient of 11.5 W/m2 K. Determine the Biot number

An iron billet (k = 65 W/m K) measuring 20 * 15 * 80 cm is exposed to a convective flow resulting in convection coefficient of 11.5 W/m2 K. Determine the Biot number Correct Answer 0.006846

B = h L C/k = 0.006846.

Related Questions

An Identity Card has the number ABCDEFG, not necessarily in that order, where each letter represents a distinct digit (1, 2, 4, 5, 7, 8, 9 only). The number is divisible by 9. After deleting the first digit from the right, the resulting number is divisible by 6. After deleting two digits from the right of original number, the resulting number is divisible by 5. After deleting three digits from the right of original number, the resulting number is divisible by 4. After deleting four digits from the right of original number, the resulting number is divisible by 3. After deleting five digits from the right of original number, the resulting number is divisible by 2. Which of the following is a possible value for the sum of the middle three digits of the number?
A polarized light of Intensity 40 Wm2 is incident on the analyzer at a certain angle. If the transmitted beam has an Intensity of 20 Wm2, the angle made with the vertical is _____________
A polarized light of Intensity 35 Wm2 is incident on the analyzer at a certain angle. If the transmitted beam has an Intensity of 30 Wm2, the angle made with the vertical is __________
A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2.K. The Biot number is
A polished metal pipe 5 cm outside diameter and 370 K temperature at the outer surface is exposed to ambient conditions at 295 K temperature. The emissivity of the surface is 0.2 and the convection coefficient of heat transfer is 11.35 W/m2 degree. Calculate the overall coefficient of heat transfer by the combined mode of convection and radiation
Forced air flows over a convection heat exchanger in a room heater, resulting in a convective heat transfer coefficient 1.136 k W/m2 K. The surface temperature of heat exchanger may be considered constant at 65 degree Celsius, and the air is at 20 degree Celsius. Determine the heat exchanger surface area required for 8.8 k W of heating
The calculation of heat transmission by convection is based on the determination of a Nusselt number or convective film coefficient. To that goal, which of the following strategies have been proposed (i) Non-dimensional analysis and experimental correlations (ii) Hydrodynamic concept of velocity boundary layer (iii) Reynolds similarity between the mechanism of fluid friction in the boundary layer and the transfer of heat by convection Identify the correct one
The determination of a value of Nusselt number or the convective film coefficient forms a basis for the computation of heat transfer by convection. Towards that end, following approaches have been suggested (i) Non-dimensional analysis and experimental correlations (ii) Hydrodynamic concept of velocity boundary layer (iii) Reynolds similarity between the mechanism of fluid friction in the boundary layer and the transfer of heat by convection Identify the correct one
A horizontal heated plate at 200 degree Celsius and facing upwards has been placed in still air at 20 degree Celsius. If the plate measures 1.25 m by 1 m, make calculations for the heat loss by natural convection. The convective film coefficient for free convection is given by the following empirical relation h = 0.32 (α) 0.25 W/m2 K Where α is the mean film temperature in degrees kelvin
Find the heat transfer rate from a hot surface for 6 fins of 10 cm length? The base temperature of the fin is maintained at 200 degree Celsius and the film is exposed to a convection environment at 15 degree Celsius with convective coefficient 25W/square m K. Each fin has cross-sectional area 2.5 square centimeter and is made of a material having thermal conductivity 250W/m K