Bissoy.com
Doctors Medicines MCQs Q&A

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa.

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. Correct Answer 5.07mm

t=D/2 -1 ].

Related Questions

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 70N/mm². Calculate the thickness of the cylinder using Clavarinoe’s equation. Diameter of the cylinder is 240mm.μ=0.3 and pressure in cylinder is 15MPa.
A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
The diameters of a small piston and a large piston of a hydraulic jack are 45 mm and 100 mm respectively.Force of 0.09 kN applied on smaller in size piston. Find load lifted by piston if smaller in size piston is 40 cm above the large piston. The density of fluid is 850 kg/m3
A tensile rod of 40kN is acting on a rod of diameter 40mm and of length 4m. a bore of diameter 20mm is made centrally on the rod. To what length the rod should be bored so that the total extension will increase 30% under the same tensile load if E = 2×105 N/mm2?
For a steam engine, the following data is given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m calculate inertia force at θ=30 degrees from IDC.
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
Find the bending stress to which a screw of nominal diameter 22mm is subjected when the clamp exerts a force of 5kN acts on it. The screw is double threaded and pitch of screw is 5mm.Given: Coefficient of friction is 0.15.It is assumed operator exerts a force of 250N at the handle of length 275mm.
The crank-pin circle radius of a horizontal engine is 300 mm. The mass of the reciprocating parts is 250 kg. When the crank has travelled 30° from T.D.C., the difference between the driving and the back pressures is 0.45 N/mm2. The connecting rod length between centres is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 r.p.m. and if the effect of piston rod diameter is neglected, calculate the net load on piston.
The figure shows a 5 cm diameter rod, 90 cm long, which is having its lower face grinded smooth. The remainder of the rod is exposed to 32 degree Celsius room air and a surface coefficient heat transfer equal to 6.8 W/m2 degree exists between the rod surface and the room air. The grinder dissipates mechanical energy at the rate of 35 W. If thermal conductivity of rod material is 41.5 W/m degree, find the temperature of the rod at the point where the grinding is taking place
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.