Bissoy.com
Doctors Medicines MCQs Q&A

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm². Correct Answer 25.5mm

σ= + , where y=t & I=t(2t)ᴲ/12.

Related Questions

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering combined effect of direct stress and bending stress.
A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum normal stress will be
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
Low quality of jute fibre is attributed to
1. Discoloration of fibre
2. Very short fibre strands
3. Reduction of cellulose in fibre
4. Reduction of cell wall strength over-retting decreases the fibre quality due to
Select the correct answer:
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)
An order was placed for the supply of carpet whose breadth was 5cm and length was 1.22 times the breadth. What would be the cost of a carpet whose length and breadth are 30% more and 15% more respectively than the corresponding length and breadth of the first carpet, given that the rate of carpet is 35 rupees per square meter?
A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.
A glass fibre reinforced epoxy composite is made with 60 wt.% unidirectional continuous glass fibres. The elastic moduli of the glass fibre and the epoxy matrix are 72.5 and 2.4 GPa, respectively. What is the elastic modulus of this composite along the fibre direction, in GPa? The densities of glass fibre and epoxy are 2.58 g/cm3 and 1.14 g/cm3, respectively
A middle school mathematics teacher asks his students to construct a rectangle with length 7 cm and breadth 4 cm. As the students completed the task, he further instructs them: (i) increase the length and breadth by 2 cm each and draw to see what figure you get (ii) decrease the length and breadth by 2 cm and draw to see what figure you get (iii) increase the length by 1 cm and decrease the breadth by 1 cm. Can you predict the type of figure without draving? Which principle of Zoltan Dienes theory of mathematics learning is he using in the above activity?