Bissoy.com
Doctors Medicines MCQs Q&A

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress. Correct Answer 3.4mm

Direct Tensile Stress=1000/0.8D² or σ (t) =1250/D² 1250/D²=110 or D=3.4mm.

Related Questions

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering combined effect of direct stress and bending stress.
A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.
If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².
If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.
Consider the following statements: 1. Cross-section of a member of truss experiences uniform stress 2. Cross-section of a beam experiences minimum stress 3. Cross-section of a beam experiences linearly varying stress 4. Cross-sections of truss members experience only compressive stress Which of the above statements are correct?
Consider the following statements with regards to the shear force diagram for the beam ABCD: 1. The beam ABCD is an overhanging beam having supports at A and D only. 2. The beam carries a point load of 20 kN at C. 3. The beam carries a concentrated load of 10 kN at the end B. 4. The beam is an overhanging beam having supports at C and D only. 5. The beam carries a uniformly distributed load of 70 kN over the left hand portion AC only. Which of the above statements are correct?
A hollow cylinder is made up of metal. The difference between the outer and the inner curved surface area of this cylinder is 352 cm2. The height of the cylinder is 28 cm. If the total surface area of this hollow cylinder is 2640 cm2, then what are the inner and outer radii (in cm)?
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the tangential stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
A hollows sphere is melted to form small identical hollows spheres. Inner and outer radius of the bigger sphere are 4 cm and 6 cm respectively. If inner and outer radii of the smaller sphere are 2 cm and 3 cm respectively, then how many spheres can be formed?