Bissoy.com
Doctors Medicines MCQs Q&A

A cast iron piece of total length 100mm is needed to be tapered for a length of 40mm using swiveling the compound rest method. Diameter of job is 20mm and smaller end have nearly zero diameter. What should the angle in degrees by which compound rest should be rotated?

A cast iron piece of total length 100mm is needed to be tapered for a length of 40mm using swiveling the compound rest method. Diameter of job is 20mm and smaller end have nearly zero diameter. What should the angle in degrees by which compound rest should be rotated? Correct Answer 14.03

tan (Angle of rotation of compound rest) = (D-d)/ (2*L), where ‘D’ is the external diameter, ‘d’ is the internal diameter, ‘L’ is the length of job.

Related Questions

Which of the following statements is most relevant in the context of Job Analysis? Choose the correct answer from the code given below. (i) Job Analysis helps in identifying the right person for the right job. (ii) A person cannot judge the job from the point of view of its suitability. (iii) Job analysis helps in job satisfaction and job efficiency. (iv) Through Job Analysis an employer cannot evaluate the prospective employee to judge his fitness or otherwise for the job. (v) Job Analysis helps in planning appropriate training programs. (vi) Job Analysis defines client needs in specific terms. (vii) Job Analysis assists in knowing the personnel specifications for various jobs.
What will be the value of diameter of big end in mm for tapered job if diameter of small end and length of job is 60mm and 1m respectively? Given half taper angle is equal to 12.4 degrees.
What will be the value of diameter of small end in mm for tapered job if diameter of big end and length of job is 60mm and 1m respectively? Given half taper angle is equal to 1.14 degrees.
Parth had the cylindrical iron piece. He drilled out a conical cavity from the iron piece. The height and radius of the conical cavity is 15 cm and 8 cm respectively which is equal to the eight and radius of cylindrical iron piece. Find the total surface area of the remaining cylindrical iron piece.
A tensile rod of 40kN is acting on a rod of diameter 40mm and of length 4m. a bore of diameter 20mm is made centrally on the rod. To what length the rod should be bored so that the total extension will increase 30% under the same tensile load if E = 2×105 N/mm2?
Malleable cast iron is produced 1. By quick cooling of cast iron. 2. By adding magnesium to molten cast iron. 3. from white cost iron by annealing. Which of the above statements is/are correct?
What will be the value of half taper angle in degrees if diameter of big end is 100mm and diameter of small end is 60mm for a 1m long job?
A sheet of paper is cut into three pieces in certain way. Length of first piece of paper is equal to average of three single digit odd prime numbers while length of second piece is equal to the sum of length of first piece and one-third the length of third piece. Length of third piece is equal to the sum of lengths of first and second pieces. Find the length of original sheet.
Two machines M1 and M2 are able to execute any of four jobs P, Q, R and S. The machines can perform one job on one object at a time. Jobs P, Q, R and S take 30 minutes, 20 minutes, 60 minutes and 15 minutes each respectively. There are 10 objects each requiring exactly 1 job. Job P is to be performed on 2 objects. Job Q on 3 objects, Job R on 1 object and Job S on 4 objects. What is the minimum time needed to complete all the jobs?
Which of the following statement is/are true?
1. Job analysis is the process of getting information about job.
2. Job analysis indicates the specific duties to be performed by the worker and the circumstance under which these duties are to be performed
3. A job description is a written record of the duties, responsibilities and conditions of the job.
4. The objective of job evaluation is to price the job rather than the man.
5. The objective of cost management is a product design.