Bissoy.com
Doctors Medicines MCQs Q&A

In an orthogonal machining operation : Uncut thickness = 0.5 mm Cutting speed = 20 m/min Rake angel = 150 Width of cut = 5 mm Chip thickness = 0.7 mm Thrust force = 200 N Cutting force = 1200 N The values of shear angle and shear strain, respectively, are

In an orthogonal machining operation : Uncut thickness = 0.5 mm Cutting speed = 20 m/min Rake angel = 150 Width of cut = 5 mm Chip thickness = 0.7 mm Thrust force = 200 N Cutting force = 1200 N The values of shear angle and shear strain, respectively, are Correct Answer 40.20 and 1.65

Related Questions

A single-point cutting tool with 120C rake angle is used to machine a steel work-piece. The depth of cut, i.e., uncut thickness is 0.81 mm. The chip thickness under orthogonal machining condition is 1.8 mm. The shear angle is approximately
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool, the cutting velocity is 90 m/min. The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm. If the orthogonal rake angle is zero and the principle cutting edge angle is 90°, the shear angle in degree is
In a single point turning tool, the side rake angle and orthogonal rake angle are equal. ϕ is the principal cutting edge angle and its range is 000. The chip flows in the orthogonal plane. The value of ϕ is closest to
If t1 denotes the uncut chip thickness and t2 denotes cut chip thickness ratio then, which of the following equation is correct about chip thickness ratio ‘r’?
Shear velocity during machining process is 0.2m/s with chip thickness ratio of 0.6. Shear angle is 30 degree and rake angle is 15 degree. What is the value of cutting velocity?
Shear velocity during the machining process is 1.2m/s with chip thickness ratio of 0.6. Shear angle is 30 degree and rake angle is 15 degree. What is the value of cutting velocity?
In an orthogonal cutting, the depth of cut is halved and the feed rate is double. If the chip thickness ratio is unaffected with the changed cutting conditions, the actual chip thickness will be
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
In the metal cutting operation, what will be the shear angle when a cutting tool has positive rake angle α = 20°. The friction angle is 40°. (Use Merchant's shear angle theory)